Пермский национальный исследовательский политехнический университет, г. ПермьЦелью исследования было установление зависимости относительного износа элект-рода от его структуры и разработка материалов для электродов-инструментов с улуч-шенными характеристиками.Рассмотрены требования к электродам-инструментам для электроэрозионной про-шивки. Композиционные материалы на основе меди с различным содержанием туго-плавкой фазы изготовлены методом порошковой металлургии. Методами рентгенофазо-вого анализа и рамановской спектроскопии обнаружено образование интеркалированно-го медью графита и sp 3 связей в графите, спеченном с медью, которые способствуют повышению электропроводности и капиллярных свойств материала.Исследовано влияние содержания тугоплавкой фазы в системах «медь -тугоплав-кий металл», «медь -графит» на пористость, твердость, прочность, электросопротив-ление, относительную износостойкость электродов-инструментов из композиционных материалов. Установлено, что с увеличением содержания тугоплавких металлов увели-чивается пористость и электросопротивление композиционных материалов. Определе-но, что относительная износостойкость при электроэрозионной прошивке электрода-инструмента из композиционных материалов на основе меди, содержащих тугоплавкие металлы, более всего зависит от жаростойкости тугоплавкого металла; в системах на основе меди с графитом относительный износ уменьшается за счет повышения элект-ропроводности и капиллярного эффекта.Ключевые слова: электроэрозионная обработка, электрод-инструмент, компози-ционный материал, рамановская спектроскопия, интеркалирование, медь, тугоплавкие металлы, графит, эрозионная стойкость Введение. Электроэрозионная обработка (ЭЭО) основана на эффекте расплавления и испа-рения микропорций материала в основном под тепловым воздействием импульсов электрической энергии. Эта энергия выделяется в канале разряда между поверхностью обрабатываемой детали и электродом-инструментом, погруженным в жидкую (обычную неэлектропроводящую) среду. Следующие друг за другом импульсные разряды производят выплавление и испарение микро-порции материала; частицы расплавленного материала выбрасываются из зоны обработки разви-вающимся в канале разряда давлением, и электрод-инструмент получает возможность внедряться в обрабатываемую деталь [1].Электроды-инструменты (ЭИ) являются одними из основных элементов, участвующих в электроэрозионном процессе. Параметры их оказывают существенное влияние на стабильность электроэрозионного процесса, его эффективность и область использования. Производительность и качество ЭЭО также находятся в зависимости от материала ЭИ. Электрод-инструмент должен изготавливаться из эрозионностойкого материала, обеспечивать стабильную работу во всем диа-пазоне рабочих режимов ЭЭО и максимальную производительность, имея малый износ [2].Разработка новых технологических процессов создания эрозионностойких материалов, об-ладающих низкой стоимостью и высокой износостойкостью, представляет собой весьма важ-ную задачу и имеет большое экономическое значение, так как эрозионный износ ...
1 Пермский национальный исследовательский политехнический университет, Пермь, Россия 2 ООО «Кедрон», Пермь, Россия ОСОБЕННОСТИ ТОЧЕНИЯ ПЛАСТИКОВ Ф-4, ПА-6, Ф-4К20Статья посвящена сравнительному исследованию стойкости режущей части инструмента (быстрорежущая сталь Р18, твердый сплав ВК8, алмаз CVD) при точении различных марок пластиков (Ф-4, ПА-6, Ф-4К20) c целью определения обрабатываемости резанием для каждой марки пластика. В лабораторных условиях подбирались оптимальные режимы резания с точки зрения обеспечения максимальной стойкости и производительности обработки. Глубина резания выбиралась равной припуску на обработку c максимальным сокращением времени обработки. Подачу выбирали из условия обеспечения требуемой шероховатости поверхности детали: для обеспечения Ra = 3,2 мкм необходима подача 0,3 мм/об, для Ra = 1,25 мкм -0,2 мм/об, для Ra = 0,63 мкм -0,1 мм/об. Скорость резания выбиралась из соображений обеспечения рационального соотношения стойкости инструмента и производительности обработки: для Ф-4 резцом из Р18 оптимальный диапазон значений скорости резания 150-200 м/мин, для ПА-6 резцом из ВК8 -250-300 м/мин, для Ф-4К20 резцом из CVD -500-600 м/мин. Сравнительные стойкостные испытания проводились в производственных условиях ООО «Кедрон» при точении деталей типа «кольцо» из трех различных марок пластиков: Ф-4, ПА-6, Ф-4К20. При обработке Ф-4 стойкость инструмента из Р18 составила Т = 250 мин, стойкость инструмента из ВК8 составила Т = 300 мин, причем применение водоэмульсионной СОЖ не оказало влияния на стойкость. При обработке ПА-6 без СОЖ стойкость инструмента из Р18 составила Т = 20 мин, стойкость инструмента из ВК8 составила Т = 150 мин; при точении с водоэмульсионной СОЖ стойкость инструмента из Р18 составила Т = 25 мин, стойкость инструмента из ВК8 составила Т = 200 мин. При обработке Ф-4К20 стойкость инструмента из ВК8 составила Т = 25 мин, а стойкость инструмента из химически осажденного алмаза CVD составила Т = 500 мин, причем применение водоэмульсионной СОЖ не оказало влияния на стойкость. Показано, что различные марки пластиков, несмотря на кажущееся сходство (как в случае материала Ф-4 и его композиции Ф-4К20), могут существенным образом отличаться друг от друга по критерию обрабатываемости резанием, что обусловлено их абразивными свойствами, которые проявляются при механической обработке.Ключевые слова: точение пластиков, обрабатываемость резанием, интенсивность износа, стойкость инструмента, алмазный резец, фторопласт, тефлон, коксонаполненный фторопласт, полиамид, капролон, качество детали, точность обработки, шероховатость, температурные деформации, остаточные напряжения.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.