No abstract

The traditional high-temperature conversion (HTC) approach toward compound-specific stable isotope analysis (CSIA) of hydrogen for heteroatom-bearing (i.e., N, Cl, S) compounds has been afflicted by fractionation bias due to formation of byproducts HCN, HCl, and H2S. This study presents a chromium-based high-temperature conversion (Cr/HTC) approach for organic compounds containing nitrogen, chlorine, and sulfur. Following peak separation along a gas chromatographic (GC) column, the use of thermally stable ceramic Cr/HTC reactors at 1100-1500 °C and chemical sequestration of N, Cl, and S by chromium result in quantitative conversion of compound-specific organic hydrogen to H2 analyte gas. The overall hydrogen isotope analysis via GC-Cr/HTC-isotope ratio mass spectrometry (IRMS) achieved a precision of better than ± 5 mUr along the VSMOW-SLAP scale. The accuracy of GC-Cr/HTC-IRMS was validated with organic reference materials (RM) in comparison with online EA-Cr/HTC-IRMS and offline dual-inlet IRMS. The utility and reliability of the GC-Cr/HTC-IRMS system were documented during the routine measurement of more than 500 heteroatom-bearing organic samples spanning a δ(2)H range of -181 mUr to 629 mUr.

A universal application of compound-specific isotope analysis of chlorine was thus far limited by the availability of suitable analysis techniques. In this study, gas chromatography in combination with a high-temperature conversion interface (GC-HTC), converting organic chlorine in the presence of H2 to gaseous HCl, was coupled to a dual-detection system, combining an ion trap mass spectrometer (MS) and isotope-ratio mass spectrometer (IRMS). The combination of the MS/IRMS detection enabled a detailed characterization, optimization, and online monitoring of the high-temperature conversion process via ion trap MS as well as a simultaneous chlorine isotope analysis by the IRMS. Using GC-HTC-MS/IRMS, chlorine isotope analysis at optimized conversion conditions resulted in very accurate isotope values (δ(37)Cl(SMOC)) for measured reference material with known isotope composition, including chlorinated ethylene, chloromethane, hexachlorocyclohexane, and trichloroacetic acids methyl ester. Respective detection limits were determined to be <15 nmol Cl on column with achieved precision of <0.3‰.

No abstract

A novel approach for the measurement of (37)Cl, (81)Br and (34)S in organic compounds containing chlorine, bromine, and sulphur is presented to overcome some of the major drawbacks of existing methods. Contemporary methods either require reference materials with the exact molecular compositions of the substances to be tested, or necessitate several laborious offline procedures prior to isotope analysis. In our online setup, organic compounds are separated by gas chromatography (GC) coupled to a high-temperature reactor. Using hydrogen as a makeup gas, the reactor achieves quantitative conversion of chlorinated, brominated and sulphurated organic compounds into gaseous hydrogen chloride (HCl), hydrogen bromide (HBr), and hydrogen sulphide (H(2)S), respectively. In this study, the GC interface was coupled to a quadrupole mass spectrometer operated in single-ion mode. The ion traces of either H(35)Cl (m/z 36) and H(37)Cl (m/z 38), H(79)Br (m/z 80) and H(81)Br (m/z 82), or H(2)(32)S (m/z 34) and H(2)(34)S (m/z 36), were recorded to determine the isotopic ratios of chlorine, bromine, and sulphur isotopes. The conversion interface presented here provides a basis for a novel method for compound-specific isotope analysis of halogenated and sulphur-containing compounds. Rapid online measurements of organic chlorine-, bromine- and sulphur-containing mixtures will facilitate the isotopic analysis of compounds containing these elements, and broaden their usage in fields of environmental forensics employing isotopic concepts.

In this study conversion conditions for oxygen gas chromatography high temperature conversion (HTC) isotope ratio mass spectrometry (IRMS) are characterised using qualitative mass spectrometry (IonTrap). It is shown that physical and chemical properties of a given reactor design impact HTC and thus the ability to accurately measure oxygen isotope ratios. Commercially available and custom-built tube-in-tube reactors were used to elucidate (i) by-product formation (carbon dioxide, water, small organic molecules), (ii) 2nd sources of oxygen (leakage, metal oxides, ceramic material), and (iii) required reactor conditions (conditioning, reduction, stability). The suitability of the available HTC approach for compound-specific isotope analysis of oxygen in volatile organic molecules like methyl tert-butyl ether is assessed. Main problems impeding accurate analysis are non-quantitative HTC and significant carbon dioxide by-product formation. An evaluation strategy combining mass spectrometric analysis of HTC products and IRMS O/O monitoring for future method development is proposed.

No abstract

No abstract