The effects of wet-end additions of cationic starches and/or carboxymethyl cellulose (CMC) on paper properties was determined by papermaking trials. The aim of this study was to mitigate the distinctive decrease in strength and stiffness due to unrestrained drying by addition of wet-end additives, while maintaining the extraordinarily high stretch potential of papers after unrestrained drying. Addition of the different polysaccharides increased the tensile index and density of the paper. The largest incgtreases in tensile index and stiffness were seen when combining cationic starches with CMC. With certain combinations of cationic starch and CMC, it was possible to increase the tensile index and stiffness of the paper, while maintaining the high elongation at break after unrestrained drying. To complement the results from the papermaking trials, adsorption of cationic starches and CMC onto cellulose nanofibril model surfaces was studied by QCM-D and SPR techniques. The additives adsorbed onto cellulose surfaces as soft gels, containing a large amount of coupled water. Adsorption of soft and malleable polysaccharide layers in the fiber-fiber joints enhanced the paper properties significantly on a macroscopic level. The softest and most swollen polysaccharide layers resulted in the largest increases in tensile index and stiffness of paper ADDRESSES OF THE AUTHORS:
Wet foams were produced via agitation and compressed air bubbling of aqueous solutions of carboxymethylated lignin (CML). Bubble size and distribution were assessed in situ via optical microscopy. Foamability, bubble collapse rate, and foam stability (half-life time) were analyzed as a function of CML concentration, temperature, pH, and air content. Dynamic changes of the CML liquid foam were monitored by light transmission and backscattering. Cellulosic fibers of different aspect ratios (long pine fibers and short birch fibers) were suspended under agitation by the liquid foams (0.6% CML in the aqueous phase) with an air (bubble) content as high as 75% in volume. Remarkably, the half-life time of fiber-laden CML foams was 10-fold higher than that of the corresponding fiber-free liquid foam. Such lignin-based foams were demonstrated, after dewatering, as a precursor for the synthesis of nonwoven, layered structures. The resulting fiber networks (paper), obtained here for the first time with lignin-based foams, were characterized for pore size distribution, lignin retention, morphology, and physical-mechanical properties (network formation quality, density, air permeability, surface roughness, and tensile and internal bond strengths). The results were compared against structures obtained from foams stabilized with an anionic surfactant (SDS) as well as those from foam-free, water-based web-laying. Remarkably, compared to SDS, the foam-formed materials produced with CML displayed better bonding and tensile strengths. Overall, CML-based foams were found to be suitable carriers of cellulosic fibers and have opened the possibility for integrating fully biobased systems in foam-forming. This is an emerging option to increase the effective solids content in the system without compromising the quality of formed nonwoven materials while achieving reductions in water and energy consumption.
Speed of paper machines is often limited by the drainage rate of the furnish and the mechanical properties of the wet web, i.e. the tension and relaxation properties. In this study, the effects of alteration of fibre properties and fines content by gentle and harsh refining on dewatering as well as on wet and dry web properties were determined. Both types of refining or addition of fines prolonged the dewatering time but also improved the mechanical properties. Harsh refining with much fibre cutting resulted in longer dewatering time, lower dry content after wet pressing and higher density of dry sheets than gentle refining with much external/internal fibrillation of fibres. Removal of fines shortened the dewatering time but decreased the wet web and dry tensile strength, and the residual tension compared to pulps containing fines. The fibre properties contributed more to the residual tension, while the fines content was more important for the wet web tensile strength. Addition of a non-ionic surfactant shortened the dewatering time of refined pulp without deteriorating the mechanical properties. By tailoring the refining and addition of surfactants, the mechanical properties of the wet web could be improved without prolonging the dewatering time.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.