No abstract

No abstract

CitationAlabbad M, Issayev G, Badra J, Voice AK, Giri BR, et al. (2018) Autoignition of straight-run naphtha: A promising fuel for advanced compression ignition engines. Combustion and Flame 189: 337-346. Available: http://dx. AbstractNaphtha, a low-octane distillate fuel, has been proposed as a promising low-cost fuel for advanced compression ignition engine technologies. Experimental and modelling studies have been conducted in this work to assess autoignition characteristics of naphtha for use in advanced engines. Ignition delay times of a certified straight-run naphtha fuel, supplied by Haltermann Solutions, were measured in a shock tube and a rapid comparison machine over wide ranges of experimental conditions (20 and 60 bar, 620 -1223 K,  = 0.5, 1 and 2). The Haltermann straight-run naphtha (HSRN) has research octane number (RON) of 60 and motor octane number (MON) of 58.3, with carbon range spanning C3 -C9. Reactivity of HSRN was compared, via experiments and simulations, with three suitably formulated surrogates: a two-component PRF (n-heptane/iso-octane) surrogate, a threecomponent TPRF (toluene/n-heptane/iso-octane) surrogate, and a six-component surrogate. All surrogates reasonably captured the ignition delays of HSRN at high and intermediate temperatures. However, at low temperatures (T < 750 K), the six-component surrogate performed the best in emulating the reactivity of naphtha fuel. Temperature sensitivity and rate of production analyses revealed that the presence of cyclo-alkanes in naphtha inhibits the overall fuel reactivity. Zero-dimensional engine simulations showed that PRF is a good autoignition surrogate for naphtha at high engine loads, however, the six-component surrogate is needed to match the combustion phasing of naphtha at low engine loads.

Combustion and Flame Rights NOTICE: this is the author's version of a work that was accepted for publication in Combustion and Flame. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Combustion and Flame,

A blend of low-octane (light and heavy naphtha) and high-octane (reformate) distillate fuels has been proposed for powering gasoline compression ignition (GCI) engines. The formulated 'GCI blend' has a research octane number (RON) of 77 and a motor octane number (MON) of 73.9. In addition to ~ 64 mole% paraffinic components, the blend contains ~ 20 mole% aromatics and ~ 15 mole% naphthenes.Experimental and modelling studies have been conducted in this work to assess autoignition characteristics of the GCI blend. Ignition delay times were measured in a shock tube and a rapid comparison machine over wide ranges of experimental conditions (20 and 40 bar, 640 -1175 K,  = 0.5, 1 and 2). Reactivity of the GCI blend was compared with experimental measurements of two surrogates: a multi-component surrogate (MCS) and a two-component primary reference fuel (PRF 77). Both surrogates capture the reactivity of the fuel quite well at high and intermediate temperatures.The MCS does a better job of emulating the fuel reactivity at low temperatures, where PRF 77 is more reactive than the GCI blend. Ignition delay times of the two surrogates are also simulated using detailed chemical kinetic models, and the simulations agree well with the experimental findings. The results of rate-of-production analyses show important role of cycloalkane chemistry in the overall autoignition behavior of the fuel at low temperatures.

Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550 -650 K, P = 10, 20, 40 bar,  = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900 -1300 K, P = 20, 40 bar,  = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100 -1400 K, P = 20 bar. Pressure timehistories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. It was found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.

No abstract

No abstract