EBEX is a NASA-funded balloon-borne experiment designed to measure the polarization of the cosmic microwave background (CMB). Observations will be made using 1432 transition edge sensor (TES) bolometric detectors read out with frequency multiplexed SQuIDs. EBEX will observe in three frequency bands centered at 150, 250, and 410 GHz, with 768, 384, and 280 detectors in each band, respectively. This broad frequency coverage is designed to provide valuable information about polarized foreground signals from dust. The polarized sky signals will be modulated with an achromatic half wave plate (AHWP) rotating on a superconducting magnetic bearing (SMB) and analyzed with a fixed wire grid polarizer. EBEX will observe a patch covering ∼1% of the sky with 8' resolution, allowing for observation of the angular power spectrum from = 20 to 1000. This will allow EBEX to search for both the primordial B-mode signal predicted by inflation and the anticipated lensing B-mode signal. Calculations to predict EBEX constraints on r using expected noise levels show that, for a likelihood centered around zero and with negligible foregrounds, 99% of the area falls below r = 0.035. This value increases by a factor of 1.6 after a process of foreground subtraction. This estimate does not include systematic uncertainties. An engineering flight was launched in June, 2009, from Ft. Sumner, NM, and the long duration science flight in Antarctica is planned for 2011. These proceedings describe the EBEX instrument and the North American engineering flight.

We describe the signal-processing logic, firmware, and software for a frequency-domain multiplexed (FDM) biasing and demodulation system that reads out Transition Edge Sensor (TES) bolometer arrays for mm-wavelength cosmology telescopes. This system replaces a mixed-signal readout backend with a much smaller, more power-efficient system relying on Field-Programmable Gate Arrays (FPGAs) for control, computation and signal processing. The new system is sufficiently robust, automated, and power efficient to be flown on stratospheric balloon-borne telescopes and is being further developed for satellite applications.

No abstract

EBEX is a balloon-borne telescope designed to measure the polarization of the cosmic microwave background radiation. During its eleven day science flight in the Austral Summer of 2012, it operated 955 spider-web transition edge sensor (TES) bolometers separated into bands at 150, 250 and 410 GHz. This is the first time that an array of TES bolometers has been used on a balloon platform to conduct science observations. Polarization sensitivity was provided by a wire grid and continuously rotating half-wave plate. The balloon implementation of the bolometer array and readout electronics presented unique development requirements. Here we present an outline of the readout system, the remote tuning of the bolometers and Superconducting QUantum Interference Device (SQUID) amplifiers, and preliminary current noise of the bolometer array and readout system.

The E and B Experiment, EBEX, is a Cosmic Microwave Background polarization experiment designed to detect or set upper limits on the signature of primordial gravity waves. Primordial gravity waves are predicted to be produced by inflation, and a measurement of the power spectrum of these gravity waves is a measurement of the energy scale of inflation. EBEX has sufficient sensitivity to detect or set an upper limit at 95% confidence on the energy scale of inflation of < 1.4 × 10 16 GeV. This article reviews our strategy for achieving our science goals and discusses the implementation of the instrument.

EBEX (the E and B EXperiment) is a balloon-borne telescope designed to measure the polarisation of the cosmic microwave background radiation. During a two week long duration science flight over Antarctica, EBEX will operate 768, 384 and 280 spider-web transition edge sensor (TES) bolometers at 150, 250 and 410 GHz, respectively. The 10-hour EBEX engineering flight in June 2009 over New Mexico and Arizona provided the first usage of both a large array of TES bolometers and a Superconducting QUantum Interference Device (SQUID) based multiplexed readout in a space-like environment. This successful demonstration increases the technology readiness level of these bolometers and the associated readout system for future space missions. A total of 82, 49 and 82 TES detectors were operated during the engineering flight at 150, 250 and 410 GHz. The sensors were read out with a new SQUID-based digital frequency domain multiplexed readout system that was designed to meet the low power consumption and robust autonomous operation requirements presented by a balloon experiment. Here we describe the system and the remote, automated tuning of the bolometers and SQUIDs. We compare results from tuning at float to ground, and discuss bolometer performance during flight.

The E and B Experiment (EBEX) was a long-duration balloon-borne cosmic microwave background (CMB) polarimeter that flew over Antarctica in 2012. We describe the experiment's optical system, receiver, and polarimetric approach and report on their in-flight performance. EBEX had three frequency bands centered on 150, 250, and 410GHz. To make efficient use of limited mass and space, we designed a 115cm 2 sr highthroughput optical system that had two ambient temperature mirrors and four antireflection-coated polyethylene lenses per focal plane. All frequency bands shared the same optical train. Polarimetry was achieved with a continuously rotating achromatic half-wave plate (AHWP) that was levitated with a superconducting magnetic bearing (SMB). This is the first use of an SMB in astrophysics. Rotation stability was 0.45% over a period of 10 hr, and angular position accuracy was 0°. 01. The measured modulation efficiency was above 90% for all bands. To our knowledge the 109% fractional bandwidth of the AHWP was the broadest implemented to date. The receiver, composed of one lens and the AHWP at a temperature of 4K, the polarizing grid and other lenses at 1K, and the two focal planes at 0.25K, performed according to specifications, giving focal plane temperature stability with a fluctuation power spectrum that had a 1/f knee at 2mHz. EBEX was the first balloon-borne instrument to implement technologies characteristic of modern CMB polarimeters, including high-throughput optical systems, and large arrays of transition edge sensor bolometric detectors with multiplexed readouts.

Our group at UC Berkeley has produced the next generation of millimeterwave spiderweb-absorber transition edge sensor (TES) bolometer technology, which was originally developed for the Atacama Pathfinder Experiment-Sunyaev Zel'dolvich (APEX-SZ) and South Pole Telescope (SPT) experiments. We will discuss the adaptation of this technology to a balloon-borne environment and to submillimeter wavelengths for the E and B Experiment (EBEX) and the Atacama Submillimeter Telescope Experiment (ASTE). Specifically, this proceedings will address the methods we used to increase the thermal contact between the TES and a heat capacity used to limit electrothermal bandwidth, increase the optical efficiency at sub-millimeter wavelengths by reducing the grid spacing of the spiderweb absorber, and reduce the saturation power of the bolometers by a factor of 4 compared to the lowest saturation power SPT bolometers by the altering the bolometer geometry.