Plastic pollution is one of the most pressing global environmental issues we face today, in part due to the continued rise in production and use of disposable plastic products. Polyolefins and polyesters are two of the most prevalent polymers in the world accounting for ∼80% of total nonfiber plastic production. Recycling, despite being intrinsically environmentally friendly and sometimes economically viable, remains at a surprisingly low level (<9% in the U.S.) with most plastic waste ending up in landfills. One reason for this low rate of recycling stems from the challenge of recycling mixed waste streams and multicomponent plastics. In mixed waste streams, physical presorting of components prior to recycling requires significant effort, which translates to added cost. For multicomponent plastics (e.g., multilayer films such as food wrappers), the individual plastic components cannot be efficiently physically separated, and they are immiscible with poor interfacial adhesion when melt reprocessed. Thus, direct recycling of mixed plastics by melt reprocessing results in products that lack desired end-use properties. In this study, we describe the synthesis of novel poly(ethylene terephthalate)−polyethylene multiblock copolymers (PET−PE MBCPs) and evaluate their utility as adhesive tie layers in multilayer films and compatibilizer additives for melt reprocessed blends. PET and PE are targeted because they are two of the most prevalent commercial polymers in the world and are high volume waste streams. The work described here demonstrates two key findings. First, the PET−PE MBCPs serve as effective adhesive tie layers between neat PET/PE films with adhesive strength comparable to that of commercially available adhesives. Second, PET/PE (80/20 wt %) blends containing ∼0.5 wt % PET−PE MBCP were melt mixed to mimic recycling mixed plastic waste, and they were found to exhibit mechanical properties better than neat PET. Overall, this study demonstrates that PET−PE MBCPs could significantly enhance the ability to recycle PET/PE mixed waste streams by serving the role as both an adhesive promoting layer and a compatibilizer additive.

The effect of polyethylene glycol (PEG) on the mechanical and thermal properties of poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) blends was examined. Overall, it was found that PEG acted as an effective plasticizer for the PLA phase in these microphase‐separated blends, increasing the elongation at break in all blends and decreasing the Tg of the PLA phase. Significant effects on other properties were also observed. The tensile strength and Young's modulus both decreased with increasing PEG content in the blends. In contrast, the elongation at break increased with the addition of PEG, suggesting that PEG acted as a plasticizer in the polymer blends. Scanning electron microscope images showed that the fracture mode of PLA changed from brittle to ductile with the addition of PEG in the polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43044.

Poly(lactic acid) (PLA) is a biobased polymer made from biomass having high mechanical properties for engineering materials applications. However, PLA has certain limited properties such as its brittleness and low heat distortion temperature. Thus, the aim of this study is to improve toughness of PLA by blending with poly(butylene succinate-co-adipate) (PBSA), the biodegradable polymer having high toughness. Polymer blends of PLA and PBSA were prepared using a twin screw extruder. The melt rheology and the thermal property of the blends were examined. Further the blends were fabricated into compression molded parts and melt-spun fiber and were subjected to tensile and impact tests. When the PBSA content was low, PBSA phase was finely dispersed in the PLA matrix. On the other hand, when the PBSA content was high, this minor phase dispersed as a large droplet. Mechanical properties of the compression molded parts were affected by the dispersion state of PBSA minor component in PLA matrix. Impact strength of the compression molded parts was also improved by the addition of soft PBSA. The improvement was pronounced when the PBSA phase was finely dispersed in PLA matrix. However, the mechanical property of the blend fibers was affected by the postdrawing condition as well as the PBSA content.

No abstract