Periodic high aspect ratio GaAs nanopillars with widths in the range of 500-1000 nm are produced by metal-assisted chemical etching (MacEtch) using n-type (100) GaAs substrates and Au catalyst films patterned with soft lithography. Depending on the etchant concentration and etching temperature, GaAs nanowires with either vertical or undulating sidewalls are formed with an etch rate of 1-2 μm/min. The realization of high aspect ratio III-V nanostructure arrays by wet etching can potentially transform the fabrication of a variety of optoelectronic device structures including distributed Bragg reflector (DBR) and distributed feedback (DFB) semiconductor lasers, where the surface grating is currently fabricated by dry etching.

We report the fabrication of degenerately doped silicon (Si) nanowires of different aspect ratios using a simple, low-cost and effective technique that involves metal-assisted chemical etching (MacEtch) combined with soft lithography or thermal dewetting metal patterning. We demonstrate sub-micron diameter Si nanowire arrays with aspect ratios as high as 180:1, and present the challenges in producing solid nanowires using MacEtch as the doping level increases in both p- and n-type Si. We report a systematic reduction in the porosity of these nanowires by adjusting the etching solution composition and temperature. We found that the porosity decreases from top to bottom along the axial direction and increases with etching time. With a MacEtch solution that has a high [HF]:[H(2)O(2)] ratio and low temperature, it is possible to form completely solid nanowires with aspect ratios of less than approximately 10:1. However, further etching to produce longer wires renders the top portion of the nanowires porous.

We demonstrate GaAs pillar array-based light emitting diodes (LEDs) with axial p-i-n junctions fabricated using a room-temperature metal-assisted chemical etching (MacEtch) method. Variations in vertical etch rates for all three doping types of GaAs are investigated as a function of etching temperature, oxidant/acid concentration ratio, and dilution of the etching solution. Control over nanopillar morphologies is demonstrated, simply through modification of the etching conditions. Optical emission enhancement from the MacEtched p-i-n GaAs nanopillar LED is observed, relative to the non-etched planar counterpart, through room-temperature photoluminescence and electroluminescence characterization.

Metal-assisted chemical etching (MacEtch) has shown tremendous success as an anisotropic wet etching method to produce ultrahigh aspect ratio semiconductor nanowire arrays, where a metal mesh pattern serves as the catalyst. However, producing vertical via arrays using MacEtch, which requires a pattern of discrete metal disks as the catalyst, has often been challenging because of the detouring of individual catalyst disks off the vertical path while descending, especially at submicron scales. Here, the realization of ordered, vertical, and high aspect ratio silicon via arrays by MacEtch is reported, with diameters scaled from 900 all the way down to sub-100 nm. Systematic variation of the diameter and pitch of the metal catalyst pattern and the etching solution composition allows the extraction of a physical model that, for the first time, clearly reveals the roles of the two fundamental kinetic mechanisms in MacEtch, carrier generation and mass transport. Ordered submicron diameter silicon via arrays with record aspect ratio are produced, which can directly impact the through-silicon-via technology, high density storage, photonic crystal membrane, and other related applications.

Metal-assisted chemical etching (MacEtch) is a simple etching method that uses metal as the catalyst for anisotropic etching of semiconductors. However, producing nano-structures using MacEtch from discrete metal patterns, in contrast to interconnected ones, has been challenging because of the difficulties in keeping the discrete metal features in close contact with the semiconductor. We report the use of magnetic field-guided MacEtch (h-MacEtch) to fabricate periodic nanohole arrays in silicon-on-insulator (SOI) wafers for high reflectance photonic crystal membrane reflectors. This study demonstrates that h-MacEtch can be used in place of conventional dry etching to produce ordered nanohole arrays for photonic devices. V C 2013 AIP Publishing LLC.

Existing theory and data cannot quantify the contribution of phonon drag to the Seebeck coefficient (S) in semiconductors at room temperature. We show that this is possible through comparative measurements between nanowires and the bulk. Phonon boundary scattering completely quenches phonon drag in silicon nanowires enabling quantification of its contribution to S in bulk silicon in the range 25-500 K. The contribution is surprisingly large (∼34%) at 300 K even at doping of ∼3 × 10(19) cm(-3). Our results contradict the notion that phonon drag is negligible in degenerate semiconductors at temperatures relevant for thermoelectric energy conversion. A revised theory of electron-phonon momentum exchange that accounts for a phonon mean free path spectrum agrees well with the data.

No abstract

No abstract