Limiting the increase in CO2 concentrations in the atmosphere, and at the same time, meeting the increased energy demand can be achieved by applying carbon capture, utilization and storage (CCUS) technologies, which hold potential as the bridge for energy and emission-intensive industries to decarbonization goals. At the moment, the only profitable industrial large-scale carbon sequestration projects are large-scale carbon dioxide enhanced oil recovery (CO2-EOR) projects. This paper gives a general overview of the indirect and direct use of captured CO2 in CCUS with a special focus on worldwide large-scale CO2-EOR projects and their lifecycle emissions. On the basis of scientific papers and technical reports, data from 23 contemporary large-scale CO2-EOR projects in different project stages were aggregated, pointing out all the specificities of the projects. The specificities of individual projects, along with the lack of standardized methodologies specific for estimating the full lifecycle emissions resulting from CO2-EOR projects, pose a challenge and contribute to uncertainties and wide flexibilities when estimating emissions from CO2-EOR projects, making the cross-referencing of CO2-EOR projects and its comparison to other climate-mitigation strategies rather difficult. Pointing out the mentioned project’s differentiations and aggregating data on the basis of an overview of large-scale CO2-EOR projects gives useful information for future work on the topic of a CO2-EOR project’s lifecycle emissions.

Migration risk assessment of the injected CO 2 is one of the fi rst and indispensable steps in determining locations for the implementation of projects for carbon dioxide permanent disposal in depleted hydrocarbon reservoirs. Within the phase of potential storage characterization and assessment, it is necessary to conduct a quantitative risk assessment, based on dynamic reservoir models that predict the behaviour of the injected CO 2 , which requires good knowledge of the reservoir conditions. A preliminary risk assessment proposed in this paper can be used to identify risks of CO 2 leakage from the injection zone and through wells by quantifying hazard probability (likelihood) and severity, in order to establish a risk-mitigation plan and to engage prevention programs. Here, the proposed risk assessment for the injection well is based on a quantitative risk matrix. The proposed assessment for the injection zone is based on methodology used to determine a reservoir probability in exploration and development of oil and gas (Probability of Success, abbr. POS), and modifi ed by taking into account hazards that may lead to CO 2 leakage through the cap rock in the atmosphere or groundwater. Such an assessment can eliminate locations that do not meet the basic criteria in regard to short-term and long-term safety and the integrity of the site. Keywordsgeological storage of CO2, preliminary risk assessment, depleted hydrocarbon reservoirs, CO2 leakage, integrity

In line with the low-carbon strategy, the EU is expected to be climate-neutral by 2050, which would require a significant increase in renewable energy production. Produced biogas is directly used to produce electricity and heat, or it can be upgraded to reach the “renewable natural gas”, i.e., biomethane. This paper reviews the applied production technology and current state of biogas and biomethane production in Europe. Germany, UK, Italy and France are the leaders in biogas production in Europe. Biogas from AD processes is most represented in total biogas production (84%). Germany is deserving for the majority (52%) of AD biogas in the EU, while landfill gas production is well represented in the UK (43%). Biogas from sewage sludge is poorly presented by less than 5% in total biogas quantities produced in the EU. Biomethane facilities will reach a production of 32 TWh in 2020 in Europe. There are currently 18 countries producing biomethane (Germany and France with highest share). Most of the European plants use agricultural substrate (28%), while the second position refers to energy crop feedstock (25%). Sewage sludge facilities participate with 14% in the EU, mostly applied in Sweden. Membrane separation is the most used upgrading technology, applied at around 35% of biomethane plants. High energy prices today, and even higher in the future, give space for the wider acceptance of biomethane use.

The European Union greenhouse gas emission reduction target can be achieved only by applying efficient technologies, which give reliable results in a very short time. Carbon capture and storage (CCS) into geological formations covers capturing CO 2 at the large point sources, its transportation and underground deposition. The CCS technology is applicable to different industries (natural gas processing, power generation, iron and steel production, cement manufacturing, etc.). Due to huge storage capacity and existing infrastructure, depleted hydrocarbon reservoirs are one of the most favourable storage options. In order to give overall cross section through CCS technology, implementation status and other relevant issues, the chapter covers EU regulation, technology overview, large-scale and pilot CCS projects, CO 2 -enhanced oil recovery (EOR) projects, geological storage components, CO 2 storage capacity, potential CO 2 migration paths, risk assessment and CO 2 injection monitoring. Permanent geological sequestration depends on both natural and technical site performance. Site selection, designing, construction and management must ensure acceptable risk rates of less than 1% over thousands of years.

Drilling fluid represents the most important fluid that must fulfill numerous important assignments during drilling operations. Many commercially available additives for water-based drilling fluid fall into the category of non-degradable and environmentally hazardous materials. Significant development in this area can be made by using biodegradable materials as additives in drilling fluids. The objective of this study was to determine whether mandarin peel powder particle size affects the properties of the drilling fluid. In this paper, mandarin peel was used in the form of a dry powder divided into particle sizes smaller than 0.1 mm, and between 0.1 mm and 0.16 mm. Mandarin peel powder was added to a water-based drilling fluid in four different concentrations (0.5, 1, 1.5, and 2% by volume of water). By increasing the mandarin peel powder concentration, the API filtration reduced up to 42%, PPT filtration significantly decreased up to 61.54%, while the rheological parameters generally increased but remained within acceptable limits. It is determined that the optimal concentration of mandarin peel powder is up to 1.5% by volume of water.