This study reports a new microfluidic system with three integrated functional devices for pumping, mixing and separation of bio-samples by utilizing micro-electro-mechanical-systems technology. By using antibody-conjugated magnetic beads, the developed system can be used to purify and enrich virus samples such that the subsequent detection of viruses can be performed with a higher sensitivity. The target viruses were first captured by the antibody coated onto the magnetic beads by using a rotary micromixer which performed the incubation process. The viruses were then purified and enriched by a magnetic field generated by planar microcoils. The integrated microfluidic system can perform the whole purification and enrichment process automatically using a rotary micropump and appropriate microvalves. In addition, a numerical simulation was also employed to optimize the design of the microcoils and to investigate the magnetic field strength and distribution. The simulation results were consistent with experimental observations. Finally, the developed system was used to successfully perform the purification and enrichment of Dengue viruses. The detectable limit of Dengue viruses was found to be as low as 10(2) pfu ml(-1) by using this approach. Therefore, the integrated microsystem can perform incubation, transportation, mixing and purification of virus samples, possibly making it a promising platform for future biological and medical applications.

This study presents a new suction-type, pneumatically driven microfluidic device for liquid delivery and mixing. The three major components, including two symmetrical, normally closed micro-valves and a sample transport/mixing unit, are integrated in this device. Liquid samples can be transported by the suction-type sample transport/mixing unit, which comprised a circular air chamber and a fluidic reservoir. Experimental results show that volume flow rates ranging from 50 to 300 ll/min can be precisely controlled during the sample transportation processes. Moreover, the transport/mixing unit can also be used as a micro-mixer to generate efficient mixing between two reaction chambers by regulating the time-phased deformation of the polydimethylsiloxane (PDMS) membranes. A mixing efficiency as high as 98.4% can be achieved within 5 s utilizing this prototype pneumatic microfluidic device. Consequently, the development of this new suction-type, pneumatic microfluidic device can be a promising tool for further biological applications and for chemical analysis when integrated into a micro-total analysis system (l-TAS) device.

This study reports an integrated microfluidic system which utilizes virus-bound magnetic bead complexes for rapid serological analysis of antibodies associated with an infection by the dengue virus. This new microfluidic system integrates one-way micropumps, a four-membrane-type micromixer, two-way micropumps and an on-chip microcoil array in order to simultaneously perform the rapid detection of immunoglobulin G (IgG) and immunoglobulin M (IgM). An IgM/IgG titer in serum is used to confirm the presence of dengue virus infection. By utilizing microfluidic technologies and virus-bound magnetic beads, IgG and IgM in the serum samples are captured. This is followed by purification and isolation of these beads utilizing a magnetic field generated from the on-chip array of microcoils. Any interfering substances in the biological fluids are washed away automatically by the flow generated by the integrated pneumatic pumps. The fluorescence-labelled secondary antibodies are bound to the surface of the IgG/IgM complex attached onto the magnetic beads. Finally, the entire magnetic complex sandwich is transported automatically into a sample detection chamber. The optical signals are then measured and analyzed by a real-time optical detection module. The entire process is performed automatically on a single chip within 30min, which is only 1/8th of the time required for a traditional method. More importantly, the detection limit has been improved to 21pg, which is about 38 times better when compared to traditional methods. This integrated system may provide a powerful platform for the rapid diagnosis of dengue virus infection and other types of infectious diseases.

No abstract

This study reports a new immunomagnetic bead-based microfluidic system for the rapid detection of influenza A virus infection by performing a simple two-step diagnostic process that includes a magnetic bead-based fluorescent immunoassay (FIA) and an end-point optical analysis. With the incorporation of monoclonal antibody (mAb)-conjugated immunomagnetic beads, target influenza A viral particles such as A/H1N1 and A/H3N2 can be specifically recognized and are bound onto the surface of the immunomagnetic beads from the specimen sample. This is followed by labeling the fluorescent signal onto the virus-bound magnetic complexes by specific developing mAb with R-phycoerythrin (PE). Finally, the optical intensity of the magnetic complexes can be analyzed immediately by the optical detection module. Significantly, the limit of detection (LOD) of this immunomagnetic bead-based microfluidic system for the detection of influenza A virus in a specimen sample is approximately 5×10(-4) hemagglutin units (HAU), which is 1024 times better than compared to conventional bench-top systems using flow cytometry. More importantly, the entire diagnostic protocol, from the purification of target viral particles to optical detection of the magnetic complexes, can be automatically completed within 15 min in this immunomagnetic bead-based microfluidic system, which is only 8.5% of the time required when compared to a manual protocol. As a whole, this microfluidic system may provide a powerful platform for the rapid diagnosis of influenza A virus infection and may be extended for diagnosis of other types of infectious diseases with a high specificity and sensitivity.