Resistive switching (RS) is an interesting property shown by some materials systems that, especially during the last decade, has gained a lot of interest for the fabrication of electronic devices, with electronic nonvolatile memories being those that have received the most attention. The presence and quality of the RS phenomenon in a materials system can be studied using different prototype cells, performing different experiments, displaying different figures of merit, and developing different computational analyses. Therefore, the real usefulness and impact of the findings presented in each study for the RS technology will be also different. This manuscript describes the most recommendable methodologies for the fabrication, characterization, and simulation of RS devices, as well as the proper methods to display the data obtained. The idea is to help the scientific community to evaluate the real usefulness and impact of an RS study for the development of RS technology.

In this paper we review the subject of oxide breakdown (BD), focusing our attention on the case of the gate dielectrics of interest for current Si microelectronics, i.e., Si oxides or oxynitrides of thickness ranging from some tens of nanometers down to about 1nm. The first part of the paper is devoted to a concise description of the subject concerning the kinetics of oxide degradation under high-voltage stress and the statistics of the time to BD. It is shown that, according to the present understanding, the BD event is due to a buildup in the oxide bulk of defects produced by the stress at high voltage. Defect concentration increases up to a critical value corresponding to the onset of one percolation path joining the gate and substrate across the oxide. This triggers the BD, which is therefore believed to be an intrinsic effect, not due to preexisting, extrinsic defects or processing errors. We next focus our attention on experimental studies concerning the kinetics of the final event of BD, during which the gate leakage increases above acceptable levels. In conditions of intrinsic BD, the leakage increase is due to the growth of damage within the oxide in localized regions. Observations concerning this damage are reviewed and discussed. The measurement of the current, voltage, and power dissipated during the BD transient are also reported and discussed in comparison with the data of structural damage. We then describe the current understanding concerning the dependence of the BD current transient on the conditions of electric field and voltage. In particular, as the oxide thickness and, as a consequence, the voltage levels used for accelerated reliability tests have decreased, the BD transient exhibits a marked change in behavior. As the stress voltage is decreased below a threshold value, the BD transient becomes slower. This recently discovered phenomenon has been termed progressive BD, i.e., a gradual growth of the BD spot and of the gate leakage, with a time scale that under operation conditions can be a large fraction of the total time to BD. We review the literature on this phenomenon, describing the current understanding concerning the dependence of the effect on voltage, temperature, oxide thickness, sample geometry, and its physical structure. We also discuss the possible relation to the so-called soft oxide BD mode and propose a simpler, more consistent terminology to describe different BD regimes. The last part of the paper is dedicated to exploratory studies, still at the early stages given the very recent subject, concerning the impact on the BD of materials for the metal-oxide-semiconductor gate stack and, in particular, metal gates.

Development of technologies for water desalination and purification is critical to meet the global challenges of insufficient water supply and inadequate sanitation, especially for pointof-use applications. Conventional desalination methods are energy and operationally intensive, whereas adsorption-based techniques are simple and easy to use for point-of-use water purification, yet their capacity to remove salts is limited. Here we report that plasma-modified ultralong carbon nanotubes exhibit ultrahigh specific adsorption capacity for salt (exceeding 400% by weight) that is two orders of magnitude higher than that found in the current stateof-the-art activated carbon-based water treatment systems. We exploit this adsorption capacity in ultralong carbon nanotube-based membranes that can remove salt, as well as organic and metal contaminants. These ultralong carbon nanotube-based membranes may lead to next-generation rechargeable, point-of-use potable water purification appliances with superior desalination, disinfection and filtration properties.

Resistive switching (RS) devices are emerging electronic components that could have applications in multiple types of integrated circuits, including electronic memories, true random number generators, radiofrequency switches, neuromorphic vision sensors, and artificial neural networks. The main factor hindering the massive employment of RS devices in commercial circuits is related to variability and reliability issues, which are usually evaluated through switching endurance tests. However, we note that most studies that claimed high endurances >106 cycles were based on resistance versus cycle plots that contain very few data points (in many cases even <20), and which are collected in only one device. We recommend not to use such a characterization method because it is highly inaccurate and unreliable (i.e., it cannot reliably demonstrate that the device effectively switches in every cycle and it ignores cycle-to-cycle and device-to-device variability). This has created a blurry vision of the real performance of RS devices and in many cases has exaggerated their potential. This article proposes and describes a method for the correct characterization of switching endurance in RS devices; this method aims to construct endurance plots showing one data point per cycle and resistive state and combine data from multiple devices. Adopting this recommended method should result in more reliable literature in the field of RS technologies, which should accelerate their integration in commercial products.

Pileup of boron atoms near the maximum melt depth in bulk silicon and silicon-on-insulator (SOI) substrates upon laser annealing (LA) was studied. The results show that boron atoms accumulate near the maximum melt depth in shallow melting and increases with increasing laser pulses. The pileup is found to be related to the recrystallization behavior of the melted silicon during LA and occurs at a recrystallization transient, RT0, of about 10nm from the maximum melt depth in both SOI and bulk silicon substrates. An abrupt recrystallization process in preamorphized silicon, on the other hand, suppresses the formation of the boron pileup during LA.