Turbofan jet engines are among the most complex and responsible constructions in the world. The creation of modern globally competitive engines is impossible without the use of digital twin technologies: a set of computational models that fully describe the behaviour of the structure under any operating conditions. Today, composite materials are widely used in many industries. In aircraft engines, their use is very promising for fan blades and fan case to reduce the overall weight of the engine and inertial loads. The dovetail joint of the fan blade works in compound stress conditions. To assess the strength of this element, it is necessary to consider a three-dimensional formulation of the problem, which requires significant computational resources. The use of composite materials is complicated by the complexity of preparing mesh models. A correct choice of the material strength criterion is another important factor that must be taken into account during the analysis of the mechanical behaviour of the thick-walled composite structures. The chosen criterion largely determines the reliability and weight efficiency of the composite structure. This paper considers the possibility of replacing the three-dimensional statement of the problem with a two-dimensional one when choosing rational reinforcing schemes for the dovetail joint of a CFRP fan blade at the initial stages using Daniel strength criterion.
The complexity of biaxial tests and analysis of their results makes it difficult to study the interlaminar shear properties of fibre-reinforced composites, particularly under through-thickness compression, which occurs in thick-walled composite elements. The improvements in experimental methods to study the features of the nonlinear behaviour of composites under biaxial loading is now an important and relevant task in the development aircraft structural elements made of сarbon fibre-reinforced polymers. This study aimed to develop a new experimental approach for the reliable determination of the interlaminar shear properties of laminates under through-thickness compression using a standard testing machine. An appropriate V-notched specimen was developed based on the configuration of well-known Iosipescu and butterfly-shaped specimens. The approach is demonstrated using woven carbon/epoxy laminates. Both the preliminary assessment of the stress fields under combined compression/shear loading and the analysis of fracture mechanisms were performed with finite-element modelling in a three-dimensional formulation. The digital image correlation (DIC) method was used to obtain experimental, full-field deformations of the specimens and to estimate the uniformity of the strain distribution in the gauge section. The stress–strain curves were obtained under biaxial loading, and the corresponding features of the composite failure behaviour were analysed in detail. It was found that the maximum compression strain on the stress–strain curves, in some cases, corresponded to the discontinuity in the composite structure. In these cases, the disproportionate changes in through-thickness strains in the gauge section of the specimens were recorded at the maximum load. With the increase in through-thickness compression stresses, the difference between the shear strength values, determined by the maximum load and the maximum compressive strain, increased by up to 20%. It was shown that the assessment of the composite strength at maximum load at the design stage significantly increased the risk of premature failure of the composite elements during exploitation.
Three-point bending tests are widely used to determine the elastic and shear moduli of polymer matrix composites due to their simplicity. Nevertheless, the accuracy of the elastic constants definition has a significant sensitivity to a degree of anisotropy of the laminates. This work is aimed to analyze experimentally and numerically the capabilities of the bending tests for determining the out-of-plane shear modulus of composites with different degrees of anisotropy. The methodology considering an influence of shear and local deformation effects was used. Finite element modeling was performed for an independent assessment of the accuracy of the methodology. It was found out that the methodology considered allowed one to determine the out-of-plane shear modulus with reasonable accuracy for both unidirectional and woven CFRPs. At the same time, the accuracy of the out-of-plane shear modulus determining is significantly reduced for materials with a low degree of anisotropy, such as woven GFRP.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.