Insufficient catalytic activity and durability are key barriers to the commercial deployment of low temperature polymer electrolyte membrane (PEM) and direct-methanol fuel cells (DMFCs). Recent observations suggest that carbon-based catalyst support materials can be systematically doped with nitrogen to create strong, beneficial catalyst-support interactions which substantially enhance catalyst activity and stability. Data suggest that nitrogen functional groups introduced into a carbon support appear to influence at least three aspects of the catalyst/support system: 1) modified nucleation and growth kinetics during catalyst nanoparticle deposition, which results in smaller catalyst particle size and increased catalyst particle dispersion, 2) increased support/catalyst chemical binding (or ''tethering''), which results in enhanced durability, and 3) catalyst nanoparticle electronic structure modification, which enhances intrinsic catalytic activity. This review highlights recent studies that provide broad-based evidence for these nitrogen-modification effects as well as insights into the underlying fundamental mechanisms.

Single-walled carbon nanotubes (SWNTs) have potential as electron acceptors in organic photovoltaics (OPVs), but the currently low-power conversion efficiencies of devices remain largely unexplained. We demonstrate effective redispersion of isolated, highly enriched semiconducting and metallic SWNTs into poly(3-hexylthiophene) (P3HT). We use these enriched blends to provide the first experimental evidence of the negative impact of metallic nanotubes. Time-resolved microwave conductivity reveals that the long-lived carrier population can be significantly increased by incorporating highly enriched semiconducting SWNTs into semiconducting polymer composites.

Networks made of single-walled carbon nanotubes (SWNTs) and metallic nanowire networks, graphene, and ultra-thin metal films have all been proposed as replacements for transparent conducting oxides (TCOs) in photovoltaic and other applications. However, only limited comparisons of nanostructured networks and TCOs are available. Several common figures of merit that are often used to compare the electrical and optical performance of the transparent contacts are evaluated here, and the merits of each method of comparison are discussed. Calculating the current loss due to absorption in the TCO is the most useful metric for evaluating new materials for use in solar cells with well-defined sheet resistance requirements and known quantum efficiencies. The 'Haacke' figure of merit, Φ H , correlates fairly well with current loss and is a good metric for evaluating electro-optical performance for more general applications. The analyses presented here demonstrate that silver nanowire networks are much closer to achieving optimal electrical and optical properties than carbon-based networks.

We have created stable dispersions of single wall carbon nanotubes (SWNTs) in water by employing a noncovalent functionalization scheme that allows carboxylic acid moieties to be attached to the SWNT surface by a pi-pi stacking interaction. Pyrenecarboxylic acid (PCA) is noncovalently attached to the surface of SWNTs and affords highly uniform and stable aqueous dispersions. This method was developed to provide a noncovalent alternative to the commonly used oxidative acid treatment functionalization of carbon nanotubes. This alternative strategy avoids the damage to the carbon nanotube structure inherent to oxidative acid treatments. Carbon nanotubes are commonly functionalized with oxidative acid treatment schemes to create polymer-nanotube composites and improve the adhesion between the polymer and carbon nanotubes. Composites of SWNTs and polycarbonate were prepared and tested to determine the effect of PCA on the adhesion of the SWNTs to the polymer matrix. These tests confirmed that PCA improved the SWNT-polycarbonate adhesion and improved the dispersion of the SWNTs throughout the matrix. This study demonstrates that stable dispersions of SWNTs can be achieved without substantial cutting, introduction of defects, or covalent modification, by employing a simple and effective noncovalent functionalization with PCA.

Monolayer to few-layer graphene thin films have several attractive properties such as high transparency, exceptional electronic transport, mechanical durability, and environmental stability, which are required in transparent conducting electrodes (TCs). The successful incorporation of graphene TCs into demanding applications such as thin film photovoltaics requires a detailed understanding of the factors controlling long-range charge transport. In this study, we use spectroscopic and electrical transport measurements to provide a self-consistent understanding of the macroscopic (centimeter, many-grain scale) transport properties of chemically doped p-type and n-type graphene TCs. We demonstrate the first large-area n-type graphene TCs through the use of hydrazine or polyethyleneimine as dopants. The n-type graphene TCs utilizing PEI, either as the sole dopant or as an overcoat, have good stability in air compared to TCs only doped with hydrazine. We demonstrate a shift in Fermi energy of well over 1 V between the n- and p-type graphene TCs and a sheet resistance of ~50 Ω/sq at 89% visible transmittance. The carrier density is increased by 2 orders of magnitude in heavily doped graphene TCs, while the mobility is reduced by a factor of ~7 due to charged impurity scattering. Temperature-dependent measurements demonstrate that the molecular dopants also help to suppress processes associated with carrier localization that may limit the potential of intrinsic graphene TCs. These results suggest that properly doped graphene TCs may be well-suited as anodes or cathodes for a variety of opto-electronic applications.