Determining of Crystalline Silica in Respirable Dust Samples by Infrared Spectrophotometry in the Presence of Interferences: Jun Ojima. National Institute of Industrial Health—Infrared Spectrophotometry (IR) is now widely used to determine crystalline silica in industrial dust samples. Though the IR method has many advantages when dealing with respirable dust samples, some serious analytical errors are often caused by interference minerals contamination. These minerals have a characteristic absorption band corresponding in position to the analytical peak for crystalline silica. In this paper, six typical interference minerals (Kaolinite, Mullite, Muscovite, Pyrophyllite, Montmorillonite and Amorphous silica) were pre‐size controlled to respirable range and their infrared spectra were measured by means of an FT‐IR with the well known potassium bromide tablet technique. The effects of these interference minerals on the Japanese OEL or the administrative control level for respirable dust which depend on the silica content were calculated and expressed in figures. The measured absorption coefficients of the interference minerals and quartz were 1.36–6.98 Abs/mg and 24.46 Abs/mg, respectively. The absorption band height ratios of each interference minerals were also measured. Then the efficiency and applicability of two spectrum correction methods for the interference minerals, absorbance ratio method and difference spectrum method were examined by using artificially mixed samples (standard interference mineral + standard quartz). By comparing the quantifying results for the mixture samples, it was revealed that the interfered spectra were almost corrected successfully when using the difference spectrum method, whereas correction by the absorbance ratio method resulted in apparent negative errors. Furthermore, the difference spectrum method was proven to be superior to the absorbance ratio method in applicability.
Visible light of short wavelength (blue light) may cause a photochemical injury to the retina, called photoretinitis or blue-light hazard. In this study, various light sources were evaluated for blue-light hazard. These sources include the sun, the arc associated with arc welding and plasma cutting, molten steel, iron and glass, the interior of furnaces, the arc or envelope of discharge lamps, the filament or envelope of incandescent lamps, the envelope of fluorescent lamps and light-emitting diodes. The spectral radiance of each light source was measured, and blue-light effective radiance and the corresponding permissible exposure time per day were calculated in accordance with the ACGIH (American Conference of Governmental Industrial Hygienists) standard. The sun, arc welding, plasma cutting and the arc of discharge lamps were found to have extremely high effective radiances with corresponding permissible exposure times of only 0.6-40 s, suggesting that viewing these light sources is very hazardous to the retina. Other light sources were found to have low effective radiances under the study conditions and would pose no hazard, at least for short exposure times.
Conventionally, the "breathing zone" is defined as the zone within a 0.3 m (or 10 inches) radius of a worker's nose and mouth, and it has been generally assumed that a contaminant in the breathing zone is homogeneous and its concentration is equivalent to the concentration inhaled by the worker. However, several studies have mentioned that the concentration is not uniform in the breathing zone when a worker is close to the contaminant source. In order to examine the spatial variability of contaminant concentrations in a worker's breathing zone, comparative measurements of personal exposure were carried out in a laboratory. In experiment, ethanol vapor was released in front of a model worker (human subject and mockup mannequin) and the vapor concentrations were measured at two different sampling points, at the nose and at the chest, in the breathing zone. Then, the effects of the sampling location and the body temperature on the exposure were observed. The ratios of nose concentration to chest concentration for the human subject and the mannequin were 0-0.2 and 0.12, respectively. The exposure level of the mannequin was about 5.5-9.3 times higher than that of the human subject.
Concentrations of fumes, ozone (O 3 ), carbon monoxide (CO), nitric oxide (NO), manganese (Mn) and total and hexavalent chromium (Cr) as well as size distribution of fumes were measured at a point corresponding to the welder's breathing zone during CO 2 -arc welding, using a welding robot and three kinds of wires. Concentrations of fumes, O 3 , CO, Mn and total-Cr were found to exceed their corresponding occupational exposure limit (OEL) values, while the concentrations of NO and Cr(VI) were below those OEL levels. Airborne concentration of Mn exceeded its OEL value, and the Mn content was 8 times higher in welding fumes than in the wire. Using an additive equation of OEL and exposure concentration of each hazardous component, health risk in welders with combined exposure to welding fumes and gases was assessed as 18.6 to 46.0 times of OEL, which exceeded the unity. This finding suggests that effective protection of welders from the exposure can be attained by use of the supplied-air respirator or combined use of a dust respirator and a local exhaust system.
Objectives: The International Agency for Research on Cancer (IARC) and Japan Society for Occupational Health (JSOH) classified wood dust as a human carcinogen. Former studies have suggested that sanding with a portable sander is one of the processes that are liable to cause highest exposure to wood dust. However, the wood dust by sanding operation has not been investigated sufficiently. In this study, the generation rate and the particle size distribution of the wood dust produced by handheld sanding operation were observed by laboratory experiments.Methods: Beech and cypress were taken as typical hard and soft wood specimen respectively, and sanded with a portable sander. Three grades of sand paper (coarse, medium, fine) were attached to the sander in turn to be tested. The quantity of the wood dust produced by the sander was measured by weighing the specimen before and after the sanding and then the generation rate of the dust was calculated.Results: Soft wood generated more dust than hard wood due to the difference in abrasion durability. A coarse sand paper produced more dust than a fine sand paper. The particles of less than 1 μm diameter were scarcely observed in the wood dust. When the specimens were sanded with a fine sand paper, the mass median aerodynamic diameters of beech dust and cypress dust were 9.0 μm and 9.8 μm, respectively.Conclusions: Respirable wood dust is able to be controlled by general ventilation with more than 0.7-4.2 m3/min ventilation rate.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.