Safety and performance of the turbo-engine in an aircraft is directly affected by the health of its blades. In recent years, several improvements to the sensors have taken place to monitor the blades in a non-intrusive way. The parameters that are usually measured are the distance between the blade tip and the casing, and the passing time at a given point. Simultaneously, several techniques have been developed that allow for the inference-from those parameters and under certain conditions-of the amplitude and frequency of the blade vibration. These measurements are carried out on engines set on a rig, before being installed in an airplane. In order to incorporate these methods during the regular operation of the engine, signal processing that allows for the monitoring of those parameters at all times should be developed. This article introduces an architecture, based on a trifurcated optic sensor and a hardware processor, that fulfills this need. The proposed architecture is scalable and allows several sensors to be simultaneously monitored at different points around a bladed disk. Furthermore, the results obtained by the electronic system will be compared with the results obtained by the validation of the optic sensor.
Typical Internet of Things (IoT) applications involve collecting information automatically from diverse geographically-distributed smart sensors and concentrating the information into more powerful computers. The Raspberry Pi platform has become a very interesting choice for IoT applications for several reasons: (1) good computing power/cost ratio; (2) high availability; it has become a de facto hardware standard; and (3) ease of use; it is based on operating systems with a big community of users. In IoT applications, data are frequently carried by means of wireless sensor networks in which energy consumption is a key issue. Energy consumption is especially relevant for smart sensors that are scattered over wide geographical areas and may need to work unattended on batteries for long intervals of time. In this scenario, it is convenient to ease the construction of IoT applications while keeping energy consumption to a minimum at the sensors. This work proposes a possible gateway implementation with specific technologies. It solves the following research question: how to build gateways for IoT applications with Raspberry Pi and low power IQRF communication modules. The following contributions are presented: (1) one architecture for IoT gateways that integrates data from sensor nodes into a higher level application based on low-cost/low-energy technologies; (2) bindings in Java and C that ease the construction of IoT applications; (3) an empirical model that describes the consumption of the communications at the nodes (smart sensors) and allows scaling their batteries; and (4) validation of the proposed energy model at the battery-operated nodes.
The measurement of the tip clearance and the time of arrival of every single blade in rotating turbo machinery is the starting point to characterize the performance of a rotating turbine. The type of sensors employed to acquire the data for this analysis are mainly non-intrusive such as optic, capacitive, eddycurrent and microwave sensors. This paper introduces the method employed to calculate the tip clearance and time of arrival of the blades using a fibre-optic probe. The time of arrival of each blade is evaluated right after detecting its pass, and before the next blade finishes passing in front of the sensor. Both parameters are available from that moment for further analyses by a post-processor device. During the acquisition of the sensor data, the maximum and minimum tip clearance and time of arrival are also computed for the current measurement and their values are also made available for post-processing. The whole algorithm has been developed in a single core using a hardware description language and implemented on a programmable logic device which allows for easy extension of the system when more than one sensor monitoring is required.
This paper presents a scalable IoT architecture based on the edge–fog–cloud paradigm for monitoring the Indoor Environmental Quality (IEQ) parameters in public buildings. Nowadays, IEQ monitoring systems are becoming important for several reasons: (1) to ensure that temperature and humidity conditions are adequate, improving the comfort and productivity of the occupants; (2) to introduce actions to reduce energy consumption, contributing to achieving the Sustainable Development Goals (SDG); and (3) to guarantee the quality of the air—a key concern due to the COVID-19 worldwide pandemic. Two kinds of nodes compose the proposed architecture; these are the so-called: (1) smart IEQ sensor nodes, responsible for acquiring indoor environmental measures locally, and (2) the IEQ concentrators, responsible for collecting the data from smart sensor nodes distributed along the facilities. The IEQ concentrators are also responsible for configuring the acquisition system locally, logging the acquired local data, analyzing the information, and connecting to cloud applications. The presented architecture has been designed using low-cost open-source hardware and software—specifically, single board computers and microcontrollers such as Raspberry Pis and Arduino boards. WiFi and TCP/IP communication technologies were selected, since they are typically available in corporative buildings, benefiting from already available communication infrastructures. The application layer was implemented with MQTT. A prototype was built and deployed at the Faculty of Engineering of Vitoria-Gasteiz, University of the Basque Country (UPV/EHU), using the existing network infrastructure. This prototype allowed for collecting data within different academic scenarios. Finally, a smart sensor node was designed including low-cost sensors to measure temperature, humidity, eCO2, and VOC.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.