Imaging techniques based on mass spectrometry or spectroscopy methods inform in situ about the chemical composition of biological tissues or organisms, but they are sometimes limited by their specificity, sensitivity, or spatial resolution. Multimodal imaging addresses these limitations by combining several imaging modalities; however, measuring the same sample with the same preparation using multiple imaging techniques is still uncommon due to the incompatibility between substrates, sample preparation protocols, and data formats. We present a multimodal imaging approach that employs a gold-coated nanostructured silicon substrate to couple surface-assisted laser desorption/ionization mass spectrometry (SALDI-MS) and surface-enhanced Raman spectroscopy (SERS). Our approach integrates both imaging modalities by using the same substrate, sample preparation, and data analysis software on the same sample, allowing the coregistration of both images. We transferred molecules from clean fingertips and fingertips covered with plasticine modeling clay onto our nanostructure and analyzed their chemical composition and distribution by SALDI-MS and SERS. Multimodal analysis located the traces of plasticine on fingermarks and provided chemical information on the composition of the clay. Our multimodal approach effectively combines the advantages of mass spectrometry and vibrational spectroscopy with the signal enhancing abilities of our nanostructured substrate.
In this work, electro-responsive shape-memory actuators were developed by incorporating a conductive heater in a dual-curing thiol-acrylate-epoxy shape-memory polymer (SMP). A conductive heater, consisting of an electrically conductive silverink track printed on Kapton ® substrate, was assembled to the SMP, taking advantage of the dual-curing processing. The shape-memory effect (SME) was activated by the heat dissipated by the Joule effect in the conductive track. Boron nitride agglomerates were dispersed in the thiol-acrylate-epoxy layers to increase thermal conductivity and achieve faster shape-recovery. A thermoelectric control unit was developed to control the shape recovery of the electro-responsive actuators and provide different activation strategies. The electrically activated SME was investigated and compared to a traditional SME based on an external heating source given by the dynamic mechanical analyzer (DMA) apparatus. Electro-responsive actuators were found extremely faster than the conventional SMPs based on external heating. The fastest recovery was obtained by the 15% boron nitride actuator, which recovered the 100% of the original shape in only 8 s. The thermoelectric controlling device provided an optimal control of the shape recovery speed based on the pulse width modulation of the heating current under the application of a low voltage (5 V).
Many sensors are developed over flexible substrates to be used as wearables, which does not guarantee that they will actually withstand being bent. This work evaluates the gas sensing performance of metal oxide devices of three different types, before and after having undergone automated, repetitive bending tests. These tests were aimed at demonstrating that the fabricated sensors were actually flexible, which cannot be taken for granted beforehand. The active layer in these sensors consisted of WO3 nanowires (NWs) grown directly over a Kapton foil by means of the aerosol-assisted chemical vapor deposition. Their response to different H2 concentrations was measured at first. Then, they were cyclically bent, and finally, their response to H2 was measured again. Sensors based on pristine WO3-NWs over Ag electrodes and on Pd-decorated NWs over Au electrodes maintained their performance after having been bent. Ag electrodes covered with Pd-decorated NWs became fragile and lost their usefulness. To summarize, two different types of truly flexible metal oxide gas sensor were fabricated, whereas a third one was not flexible, despite being grown over a flexible substrate following the same method. Finally, we recommend that one standard bending test procedure should be established to clearly determine the flexibility of a sensor considering its intended application.
Indium oxide octahedral nanopowders were obtained from an ionic precursor compound after an oxidation process conducted under a low-oxygen atmosphere. This method was found to produce contamination-free indium oxide nanomaterial with very similar morphological and crystalline properties to the one produced by vapor-phase transport, but at significantly lower temperatures and higher yield. The as-synthesized indium oxide was mixed to an organic vehicle and microdrop deposited to form a film bridging the interdigitated silver electrodes patterned on top of a flexible, polyimide (Kapton®), substrate. The gas sensing properties of the flexible chemoresistors towards ammonia vapors, hydrogen, and nitrogen dioxide were investigated. It was found that these sensors were remarkably sensitive to nitrogen dioxide at a low operating temperature of 150 °C. These results are consistent with the performance of vapor-phase transport synthesized indium oxide octahedra sensors on rigid, ceramic substrates. Therefore, the results presented here pave the way for the mass production of inexpensive gas sensors onto flexible substrates via additive manufacturing.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.