This paper describes the use of fiber-optic distributed temperature systems to monitor production from BP's Azeri field in Azerbaijan and highlights the benefits and issues encountered during the start-up of the first production wells. Production from BP's Azeri field in the Caspian Sea commenced in February 2005. These offshore wells are completed across multiple sand intervals using sand screens with gravel packs. Each fiber-optic monitoring system was installed with the completion in a purpose-built groove in the side of the gravel-pack screen. The screen is connected to the upper completion string via a hydraulic wet-connect enabling fiber passage from surface to total depth. The primary Azeri reservoir consists of multiple sand bodies in the Pereriv formation. Commingled completions across these sand bodies are providing wells capable of producing more than 40,000bopd. The issues that dictate the requirement for regular distributed temperature (DTS) monitoring are long, high-angle well bores and the need to understand well and reservoir performance by sand body. Additionally, the requirement for minimal production interruptions during the early years of field life does not favor conventional production logging, which would also cause interruptions to the drilling program. A thermal model is used to analyze the producing well temperature profiles and calculate the flow contribution from each of the producing zones. The results demonstrate that, once deployed, permanently installed fiber-optic distributed temperature monitoring is a cost-effective and low-risk method of monitoring multiple-pay sand screen completions without having to reduce production rates to allow conventional production logging to be carried out. The Azeri Reservoir The Azeri, Chirag and Ganashly reservoirs are located offshore Azerbijan Fig 1 and are being developed by a consortium of oil companies with BP as operator. The reservoirs are part of a multilayered sandstone anticline with approximately 5 billion barrels of reserves in place. The Azeri field is located at the south end of the anticline and it's north flank dips steeply at about 35 degrees and has a 1,000 meter oil column between the gas/oil and water/oil contacts. The south flank dips less steeply (20 degrees) and is suspected having perched oil/water contacts. Voidage support will be achieved by both water and gas injection and effective voidage replacement is considered critical to optimum reservoir drainage. The high deviation producing wells will be mostly completed with sand screens and are capable of up to 50,000bopd flow rates Fig 2. The main Azeri producing reservoir is the Pereriv formation that consists of interbedded layers of soft sand and shale. The main technical challenges being addressed by BP are:Sand control issues in the soft sands - requiring sand screens and gravel packs.Well performance and management issues in the high angle long well bores.Reservoir uncertainty, gas-oil and water-oil contact location and movement over time. Studies show that more than 100 million barrels of the secondary reserves are at risk because of poor voidage, thus a comprehensive reservoir surveillance program is required in order to minimize this risk.
BP is developing its Azeri field using deviated gravel-packed sand-screen completions producing from the multilayered Pereriv B, C, and D reservoirs. Restricted wellhead access, high rates, and differential depletion of the different reservoir intervals limit conventional production logging possibilities, so BP has chosen to install permanent fiber-optic distributed temperature monitoring systems with its sand screens and to use these systems to monitor production rates and changes over time. The optic fiber has been installed on the periphery of the sand-screen shroud, effectively installing it in the gravel-packed annulus. When the gravel pack is completed, the fiber responds to the reservoir temperature plus the effect of Joule-Thomson warming of the flowing oil caused by the pressure drop (drawdown) in the near-wellbore region. Thermal mixing of the oil with flow from below only occurs once the flow has passed through the sand-screen wire-wrap. Thus a direct measure of each individual reservoir drawdown is obtained from the difference between the fiber-measured temperature and the geothermal temperature in the flowing reservoir intervals. Given the reservoir drawdown, the flow rate can then be calculated. Thus installing the fiber outside the sand-screens gives a unique, direct measurement of individual reservoir layer drawdowns, enabling the effects of differential depletion to be monitored over time. This paper outlines the completion technology used to install the fibers along the sand screens and shows the data and results obtained where reservoirs with different pressures are commingled through gravel-packed sand-screens. Thermal models of the near-well environment are described and used to analyze the data and to obtain the flow profile and reservoir layer pressures. The use of permanently installed fiber-optic distributed temperature monitoring systems on its Azeri reservoir has allowed BP to acquire early time-surveillance data, adding significant value by reducing the voidage risk to the secondary reserves. Introduction The Azeri-Chirag-Gunashli (ACG) complex of reservoirs are located offshore Azerbaijan in the South Caspian region and extend a total of 48 km along their axis (Fig. 1). The fields were discovered between 1979 and 1987 and first production occurred in 1980. The Azeri field constitutes the south-eastern culmination of the structure and is being developed by a consortium of oil companies with BP as operator. The main producing formations are the Pereriv units B, C, and D which consist of laterally continuous layers of sandstones with excellent intrafield connectivity and permeability, interbedded with shaly layers. The reservoirs are part of a multilayered sandstone anticline with approximately 5 billion barrels of reserves in place. The field's north flank dips steeply at about 35 degrees and has a 1000-m oil column between the gas/oil and water/oil contacts. The south flank dips less steeply (20 degrees) and is suspected of having perched oil/water contacts. Voidage support will be achieved by both water and gas injection, and effective voidage replacement is considered critical to optimum reservoir drainage (Fig. 2). The development strategy of the Azeri field requires a good understanding of the production and injection conformance both geographically as well as by formation. Similarly, monitoring the gas-oil ratio (GOR) in the producers as well as water injection conformance is critical for a robust reservoir management strategy. The high-deviation producing wells will be mostly completed with sand screens and are capable of up to 50,000 BOPD flow rates. The main technical challenges being addressed by BP are:Sand control issues in the soft sands - requiring sand screens and gravel packs.Well performance and management issues in the high-angle, long well bores.Reservoir uncertainty, gas-oil and water-oil contact location, and movement over time.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.