Carbon fibers have the combined mechanical and electrochemical properties needed to make them particularly well suited for usage as electrodes in a structural lithium-ion battery, a material that simultaneously works as a battery and a structural composite. Presented in this paper is an evaluation of commercial polyacrylonitrile-based carbon fibers in terms of capacity and coulombic efficiency, as well as a microstructural and surface evaluation. Some polyacrylonitrile based carbon fibers intercalate lithium ions, resulting in a similar capacity as state-of-the-art graphite based electrodes, presently the most commonly used negative electrode material. Using high precision coulometry, we found a capacity of around 250-350 mAh/g and a very high coulombic efficiency of over 99.9% after ten cycles, which is even higher than a commercial state-of-the art graphitic electrode evaluated as reference. The high coulombic efficiency is attributed to the very low surface area of the carbon fibers, resulting in a small and stable solid-electrolyte interface layer. A highly graphitized ultra high modulus carbon fiber was evaluated as well and, compared to the other fibers, less lithium was inserted (corresponding to approximately 150 mAh/g). We show that the use of carbon fibers as an electrode material in a structural composite battery is indeed viable. The demand for new and improved battery technologies is continuously rising. In particular the electrification of the transportation sector needs innovative new solutions to develop and meet new demands. Much research is dedicated to pushing the limits of lithium (Li)-ion batteries in terms of energy, power, safety, cost, lifetime and environmental aspects.Improving graphite and other carbon based electrodes has been extensively researched since the beginning of the 90s since they are the dominating type of negative electrodes in Li-ion batteries.1-5 Another way of improving the effectiveness at a system level is through so called multifunctional battery technologies. The idea is to let the battery perform several functions, in particular carry a mechanical load and still maintain the energy storage function. The weight at a system level can be reduced, and a performance enhancement can be achieved, even if the battery function is not on par with conventional state of the art Li-ion batteries. Batteries could be included as an integral part of the structure in different kinds of vehicles, such as cars or even airplanes. Multifunctionality of materials for battery and capacitor applications has been researched in various ways for a number of years. [6][7][8][9][10][11][12][13]
Carbon fibres (CFs), originally made for use in structural composites, have also been demonstrated as high capacity Li-ion battery negative electrodes. Consequently, CFs can be used as structural electrodes; simultaneously carrying mechanical load and storing electrical energy in multifunctional structural batteries. To date, all CF microstructural designs have been generated to realise a targeted mechanical property, e.g. high strength or stiffness, based on a profound understanding of the relationship between the graphitic microstructure and the mechanical performance. Here we further advance this understanding by linking CF microstructure to the lithium insertion mechanism and the resulting electrochemical capacity. Different PAN-based CFs ranging from intermediate-to high-modulus types with distinct differences in microstructure are characterised in detail by SEM and HR-TEM and electrochemical methods. Furthermore, the mechanism of Li-ion intercalation during charge/discharge is studied by in situ confocal Raman spectroscopy on individual CFs. RamanG band analysis reveals a Li-ion intercalation mechanism in the high-modulus fibre reminiscent of that in crystalline graphite. Also, the combination of a relatively low capacity of the highmodulus CFs (ca. 150 mAh/g) is shown to be due to that the formation of a staged structure is frustrated by an obstructive turbostratic disorder. In contrast, intermediate-modulus CFs, which have significantly higher capacities (ca. 300 mAh/g), have Raman spectra indicating a Li-ion insertion mechanism closer to that of partly disordered carbons. Based on these findings, CFs with improved multifunctional performance can be realized by tailoring the graphitic order and crystallite sizes.
Lignin-based carbon fibers (LCFs) from the renewable resource softwood kraft lignin were synthesized via oxidative thermostabilization of pure melt-spun lignin and carbonization at different temperatures from 1000°C to 1700°C. The resulting LCFs were characterized by tensile testing, scanning electron microscopy (SEM), X-ray diffraction (XRD) and confocal Raman spectroscopy. The microstructure is mainly amorphous carbon with some nanocrystalline domains. The strength and stiffness are inversely proportional to the carbonization temperature, while the LCFs carbonized at 1000°C exhibit a strength of 628 MPa and a stiffness of 37 GPa. Furthermore, the application potential of LCFs was evaluated as negative electrodes in a lithium-ion battery (LIB) by electrochemical cycling at different current rates in a half-cell setup. The capacity drops with the carbonization temperature and the LCFs carbonized at 1000°C have a capacity of 335 mAh g−1. All LCFs showed good cycling stability. Because of the mechanical integrity and conductivity of the LCFs, there is no need to apply current collectors, conductive additives or binders. The advantage is an increased gravimetric energy density compared to graphite, which is the most common negative electrode material. LCFs show a promising multifunctional behavior, including good mechanical integrity, conductivity and an ability to intercalate lithium for LIBs.
We demonstrate a flexible combined electrochemistry and fiber optics-based in situ UV/vis spectroscopy setup to gain insight into the depth evolution of electrochemical hydride and oxide formation in Pd films with thicknesses of 20 and 100 nm. The thicknesses of our model systems are chosen such that the films are thinner or significantly thicker than the optical skin depth of Pd to create two distinctly different situations. Low power white light is irradiated on the sample and analyzed in three different configurations; transmittance through, and, reflectance from the front and the back side of the film. The obtained optical sensitivities correspond to fractions of a monolayer of adsorbed or absorbed hydrogen (H) and oxygen (O) on Pd. Moreover, a combined simultaneous readout obtained from the different optical measurement configurations provides mechanistic insights into the depth-evolution of the studied hydrogenation and oxidation processes.
Flexible, low-weight electrodes with integrated current collectors based on chopped polyacrylonitrile carbon fibers (CF) were produced using an easy, aqueous fabrication process, where only 4 wt% of TEMPO-oxidized cellulose nanofibrils (CNF) were used as the binder. A flexible full cell was assembled based on a LiFePO 4 (LFP) positive electrode with a CF current collector and a current collector-free CF negative electrode. The cell exhibited a stable specific capacity of 121 mAh g −1 based on the LFP weight. The CF in the negative electrode acted simultaneously as active material and current collector, which has a significant positive impact on energy density. Stable specific capacities of the CF/CNF negative electrode of 267 mAh g −1 at 0.1 C and 150 mAh g −1 at 1 C are demonstrated. The LFP/CNF with CF/CNF, as the current collector positive electrode (LFP-CF), exhibited a good rate performance with a capacity of~150 mAh g −1 at 0.1 C and 133 mAh g −1 at 1 C. The polarization of the LFP-CF electrode was similar to that of a commercial Quallion LFP electrode, while much lower compared to a flexible LFP/CNF electrode with Al foil as the current collector. This is ascribed to good contact between the CF and the active material.
We investigate hard carbon fibers at different states of charge by a combination of 7Li-NMR and 2D-XRD. In particular, we record the quadrupole-split 7Li-NMR spectra and 7Li longitudinal relaxation over...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.