BackgroundThis study focused on the unique aspect of investigating shoulder morphometric differences between 2 distinct populations.MethodsWe used 90 computed tomography images of cadaveric shoulders for this study; 45 scans belonged to the South African (SA) cohort (49.74 ± 15.4 years) and the rest were Swiss (CH; 53.8 ± 21 years). The articulating surfaces of the glenohumeral joint were extracted, and their morphometric features, such as head circular diameter, glenoid and humeral head radius of curvature, head height, and humeral height, were measured.ResultsThe mean interpopulation difference in the circular diameter of the humerus was 2.0 mm (P = .017) and 1.86 mm (P > .05) in the anterior-posterior and superior-inferior directions, respectively. The difference in the radius of curvature between the populations was 1.17 mm (P = .037). The SA shoulders were found to be longer than the CH shoulders by 8.4 mm (P > .05). There was no significant difference in the glenoid radius of curvature. The SA shoulders had higher glenohumeral mismatch (P = .005) and lower conformity index (P = .001) in comparison to the CH shoulders.ConclusionThis study presents anatomic differences between African and European glenohumeral articulating surfaces. The results suggest that the glenohumeral geometry is both gender and population specific, and future joint replacements may be designed to address these differences.

Open Reduction and Internal Fixation (ORIF) of scapula fractures have increased in numbers recently. This is due to better functional outcomes achieved post-ORIF than non-operative management techniques. In South Africa, there is only one available supplier for anatomical contoured scapula plates used in the ORIF. This study examines the fit of these plates on the bony topology of fifty healthy scapula. It was observed that the short medial body plate performed the best in adhering to the bone topology followed by the short acromion plate. The glenoid plate and the long acromion and body plates were not adequately designed to fit their intended regions on the scapula. In conclusion, this study highlights the drawbacks in design of current commercial plates available for ORIF of scapula. Further studies are needed in order to evaluate the quantitative-fit performance of these plates on fracture scapula surfaces.

Introduction: Surgical treatment of displaced acromial and scapula spine fractures may be challenging due to the bony anatomy and variable fracture patterns. This difficulty is accentuated by the limitations of the available scapular plates for fracture fixation. This study compares the quantitative fitting of anatomic scapular plates and clavicle plates, using three-dimensional (3D) printed fractured scapulae. Methods: Fourteen scapulae with acromion and spine fractures were used for this study. Computerized tomographic (CT) scans of the fractured scapulae were obtained from the Philips picture archiving and communication system (PACS) database of patients admitted to a tertiary teaching hospital in Cape Town, South Africa between 2012 and 2016. The reconstructed scapulae were 3D printed and the anatomical acromion and clavicle plates were templated about the fracture regions. The fit assessment was performed by five observers who classified the plates as no-fit, intermediate fit, and anatomical fit according to the surgical guidelines. Results: The 6-hole anterior clavicle plate performed better than any of the scapular plates as they were able to fit 45.7% of the fractured acromion, including the spine. Among the pre-contoured anatomical scapula plates, both the short and the long acromion plates could fit only 27.3% of the fractured acromion. The intraclass correlation coefficient was 0.965 suggesting excellent consensus among the five observers. Conclusion: Clavicle plates were found to be better suited to fit around a scapula fracture in its acromion and spine region.

Objectives To investigate the mortality rate for neck of femur fractures treated with arthroplasty at a tertiary level unit in South Africa and to evaluate the effect of known risk factors for mortality in neck of femur fractures treated with arthroplasty in the South African context. Design Retrospective cohort study. The main outcome was to determine mortality rates during in hospital stay, at 3 months, 6 months 1 year post surgery. The secondary outcome was to determine factors influencing mortality at 30 days, 6 months and 12 months post-surgery. Results Mortality rate was 3.3% in hospital, 5.6% at 30 days and 26.7% at 1 year. Age >79, ASA score >3, and cementing of the femur had statistically increased mortality risk ( P < .001). Average length of hospital stay was 12.3 ± 5.1 days (range 3.0-41.0 days) with 73% of patients discharged back to pre-hospital home. Conclusion Mortality rates after femur neck fracture arthroplasty in South Africa are slightly higher at 1 year compared to international data. However, the rates are comparably low during hospital stay, 30 day and at 6 months post-surgical intervals.