The physics programme and the design are described of a new collider for particle and nuclear physics, the Large Hadron Electron Collider (LHeC), in which a newly built electron beam of 60 GeV, to possibly 140 GeV, energy collides with the intense hadron beams of the LHC. Compared to the first ep collider, HERA, the kinematic range covered is extended by a factor of twenty in the negative four-momentum squared, Q 2 , and in the inverse Bjorken x, while with the design luminosity of 10 33 cm −2 s −1 the LHeC is projected to exceed the integrated HERA luminosity by two orders of magnitude. The physics programme is devoted to an exploration of the energy frontier, complementing the LHC and its discovery potential for physics beyond the Standard Model with high precision deep inelastic scattering measurements. These are designed to investigate a variety of fundamental questions in strong and electroweak interactions. The LHeC thus continues the path of deep inelastic scattering (DIS) into unknown areas of physics and kinematics. The physics programme also includes electron-deuteron and electron-ion scattering in a (Q 2 1/x) range extended by four orders of magnitude as compared to previous lepton-nucleus DIS experiments for novel investigations of neutron's and nuclear structure, the initial conditions of Quark-Gluon Plasma formation and further quantum chromodynamic phenomena. The LHeC may be realised either as a ring-ring or as a linac-ring collider. Optics and beam dynamics studies are presented for both versions, along with technical design considerations on the interaction region, magnets including new dipole prototypes, cryogenics, RF, and further components. A design study is also presented of a detector suitable to perform high precision DIS measurements in a wide range of acceptance using state-ofthe art detector technology, which is modular and of limited size enabling its fast installation. The detector includes tagging devices for electron, photon, proton and neutron detection near to the beam pipe. Civil engineering and installation studies are presented for the accelerator and the detector. The LHeC can be built within a decade and thus be operated while the LHC runs in its high-luminosity phase. It so represents a major opportunity for progress in particle physics exploiting the investment made in the LHC.

The construction of a 4 GeV superconducting proton linac (the SPL) is now part of the long term plan of CERN, and the construction of Linac4, its low-energy front end, has begun. For mid-2012 the existing conceptual design of the SPL has to be refined and transformed into a project proposal. As a first step, basic parameters like rf frequency, accelerating gradient, and operating temperature of the superconducting cavities have been reassessed, taking into account the experience accumulated in the world during the recent years, especially for the Spallation Neutron Source (SNS) in Oakridge and the International Linear Collider (ILC) projects. The conclusions confirm the validity of the initial choices, namely, the rf frequency of 704.4 MHz and the cooling temperature of % 2 K. However, the assumed gradients are estimated as optimistic: additional tests are necessary during the coming years to properly define the values to be used in the SPL design. This analysis is documented and its results are explained in this report.

A proton beam with the basic structure defined by the the LHC requirements, was first available for injection into the SPS in 1998. At the end of 2002, following a significant beam-studies and RF hardware upgrade programme, a beam having both the nominal LHC intensity and the correct longitudinal parameters was obtained at top energy for the first time. This beam, characterised by high local density, must satisfy strict requirements on bunch length, longitudinal emittance and bunch to bunch phase modulation for extraction to the LHC, where only very limited particle losses are acceptable. The problems to be solved came mainly from the high beam loading and microwave and coupled bunch instabilities which led both to beam losses and to unacceptably large longitudinal emittance on the flat top. In this paper the steps taken to arrive at these nominal beam parameters are presented. Large Hadron Collider Project NOMINAL LONGITUDINAL PARAMETERS FOR THE LHC BEAM IN THE CERN SPSP. Baudrenghien, T. Bohl, T. Linnecar, E. Shaposhnikova and J. Tuckmantel, CERN, Geneva, Switzerland Abstract A proton beam with the basic structure defined by the the LHC requirements, was first available for injection into the SPS in 1998. At the end of 2002, following a significant beam-studies and RF hardware upgrade programme, a beam having both the nominal LHC intensity and the correct longitudinal parameters was obtained at top energy for the first time. This beam, characterised by high local density, must satisfy strict requirements on bunch length, longitudinal emittance and bunch to bunch phase modulation for extraction to the LHC, where only very limited particle losses are acceptable. The problems to be solved came mainly from the high beam loading and microwave and coupled bunch instabilities which led both to beam losses and to unacceptably large longitudinal emittance on the flat top. In this paper the steps taken to arrive at these nominal beam parameters are presented.

Higher order modes (HOMs) can severely limit the operation of superconducting cavities in a linear accelerator with high beam current, high duty factor, and complex pulse structure. The full HOM spectrum has to be analyzed in order to identify potentially dangerous modes already during the design phase and to define their damping requirements. For this purpose a dedicated beam simulation code simulation of higher order mode dynamics (SMD) focused on beam-HOM interaction was developed, taking into account important effects like the HOM frequency spread, beam input jitter, different chopping patterns, as well as klystron and alignment errors. Here, SMD is used to investigate the influence of HOMs in detail in the superconducting proton linac at CERN and their potential to drive beam instabilities in the longitudinal and transverse plane.

No abstract