Abstract:A review on applications of metal-based inkjet inks for printed electronics with a particular focus on inks containing metal nanoparticles, complexes and metallo-organic compounds. The review describes the preparation of such inks and obtaining conductive patterns by using various sintering methods: thermal, photonic, microwave, plasma, electrical, and chemically triggered. Various applications of metal-based inkjet inks (metallization of solar cell, RFID antennas, OLEDs, thin film transistors, electroluminescence devices) are reviewed.

No abstract

The mechanism of polycation cytotoxicity and the relationship to polymer molecular weight is poorly understood. To gain an insight into this important phenomenon a range of newly synthesized uniform (near monodisperse) linear polyethylenimines, commercially available poly(L-lysine)s and two commonly used PEI-based transfectants (broad 22 kDa linear and 25 kDa branched) were tested for their cytotoxicity against the A549 human lung carcinoma cell line. Cell membrane damage assays (LDH release) and cell viability assays (MTT) showed a strong relationship to dose and polymer molecular weight, and increasing incubation times revealed that even supposedly "non-toxic" low molecular weight polymers still damage cell membranes. The newly proposed mechanism of cell membrane damage is acid catalysed 3 hydrolysis of lipidic phosphoester bonds, which was supported by observations of the hydrolysis of DOPC liposomes.

Structural electrolytes' retain the desirable mechanical characteristics of structural (epoxy) resins whilst introducing sufficient ionic conductivity to operate as electrolytes in electrochemical devices. Here, a series of ionic liquid-epoxy resin composites were prepared to identify the optimum system microstructure required to achieve a high level of multifunctionality. The ionic conductivity, mechanical properties, thermal stability and morphology of the cured epoxy based structural electrolytes were studied as a function of phase composition for three fully formulated high performance structural epoxy systems. At only 30 wt% of structural resin and 70 wt% of ionic liquid based electrolyte, stiff monolithic plaques with thicknesses of 2-3 mm were obtained with a room temperature ionic conductivity of 0.8 mS cm À1 and a Young's modulus of 0.2 GPa. This promising performance can be attributed to a long characteristic length scale spinodal microstructure, suggesting routes to further optimisation in the future.

The mass production technique of gravure contact printing is used to fabricate state‐of‐the art polymer field‐effect transistors (FETs). Using plastic substrates with prepatterned indium tin oxide source and drain contacts as required for display applications, four different layers are sequentially gravure‐printed: the semiconductor poly(3‐hexylthiophene‐2,5‐diyl) (P3HT), two insulator layers, and an Ag gate. A crosslinkable insulator and an Ag ink are developed which are both printable and highly robust. Printing in ambient and using this bottom‐contact/top‐gate geometry, an on/off ratio of >104 and a mobility of 0.04 cm2 V−1 s−1 are achieved. This rivals the best top‐gate polymer FETs fabricated with these materials. Printing using low concentration, low viscosity ink formulations, and different P3HT molecular weights is demonstrated. The printing speed of 40 m min−1 on a flexible polymer substrate demonstrates that very high‐volume, reel‐to‐reel production of organic electronic devices is possible.

No abstract

Main chain and branched polyrotaxanes have been synthesized in which polymerization and rotaxane formation occur simultaneously, due to the presence of the catalytically active self-threading macrocycle cucurbit[6]uril. Using monomers that contain stopper groups to prevent the catalytic macrocycle from noncatalytic threading, it was possible to prepare polyrotaxanes in high yields with molecular weights up to 39000. These polyrotaxanes are structurally perfect in the sense that exactly two macrocycles are threaded onto each structural repeat unit. Investigations into the polymerization mechanism have demonstrated that the catalyst cucurbit[6]uril is highly sensitive toward the structure of the monomers employed and a poorly designed monomer may result in complete inactivity. Features of the mechanism are discussed in some detail.

No abstract