The storage/utilization of solar energy is a promising strategy to alleviate current disparities in energy shortage Direct conversion of solar light into chemical energy by means of photocatalysis or photoelectrocatalysis is currently a point of focus for sustainable energy development and environmental remediation. However, its current efficiency is still far from satisfying, suffering especially from severe charge recombination. To solve this problem, the piezo-phototronic effect has emerged as one of the most effective strategies for photo(electro)catalysis. Through the integration of piezoelectricity, photoexcitation, and semiconductor properties, the built-in electric field by mechanical stimulation induced polarization can serve as a flexible autovalve to modulate the charge-transfer pathway and facilitate carrier separation both in the bulk phase and at the surfaces of semiconductors. This review focuses on illustrating the trends and impacts of research based on piezo-enhanced photocatalytic reactions. The fundamental mechanisms of piezo-phototronics modulated band bending and charge migration are highlighted. Through comparing and classifying different categories of piezo-photocatalysts (like the typical ZnO, MoS 2 , and BaTiO 3 ), the recent advances in polarization-promoted photo(electro)catalytic processes involving water splitting and pollutant degradation are overviewed. Meanwhile the optimization methods to promote their catalytic activities are described. Finally, the outlook for future development of polarization-enhanced strategies is presented.

Triboelectric nanogenerators (TENGs) are attracting more and more attention since they can convert various mechanical energies into electric energy. However, in traditional TENGs for harvesting rotation energy, most of the contacts between two triboelectric materials are rigid-to-rigid contact with very large friction force, which limits their practical application. Here, we report an ultra-low-friction triboelectric-electromagnetic hybrid nanogenerator (NG). A freestanding mode TENG and a rotating electromagnetic generator (EMG) are integrated together to realize the complementary individual merits. The very soft and elastic contact between the two triboelectric materials in the TENG results into very small friction force. The influences of the type and the dimensions of the dielectric material on the performance of the TENG are studied systematically from theory to experiments. The results indicate that the open-circuit voltage and the transfer charge of the TENG increase with the rotation speed, which is very different from a traditional rotary TENG and is due to the increase of the contact area. The optimized TENG has a maximal load voltage of 65 V and maximal load power per unit mass of 438.9 mW/kg under a speed rotation of 1000 rpm, while the EMG has a maximal load voltage of 7 V and maximal load power density of 181 mW/kg. This demonstration shows that the hybrid NG can power a humidity/temperature sensor by converting wind energy into electric energy when the wind speed is 5.7 m/s. Meanwhile, it can be used as a self-powered wind speed sensor to detect wind speed as low as 3.5 m/s.

The development of the Internet of Things has brought new challenges to the corresponding distributed sensor systems. Self-powered sensors that can perceive and respond to environmental stimuli without an external power supply are highly desirable. In this paper, a self-powered wind sensor system based on an anemometer triboelectric nanogenerator (a-TENG, free-standing mode) and a wind vane triboelectric nanogenerator (v-TENG, single-electrode mode) is proposed for simultaneously detecting wind speed and direction. A soft friction mode is adopted instead of a typical rigid friction for largely enhancing the output performance of the TENG. The design parameters including size, unit central angle, and applied materials are optimized to enhance sensitivity, resolution, and wide measurement scale. The optimized a-TENG could deliver an open-circuit voltage of 88 V and short-circuit current of 6.3 μA, corresponding to a maximum power output of 0.47 mW (wind speed of 6.0 m/s), which is capable of driving electronics for data transmission and storage. The current peak value of the a-TENG signal is used for analyzing wind speed for less energy consumption. Moreover, the output characteristics of a v-TENG are further explored, with six actual operation situations, and the v-TENG delivers fast response to the incoming wind and accurately outputs the wind direction data. As a wind sensor system, wind speed ranging from 2.7 to 8.0 m/s can be well detected (consistent with a commercial sensor) and eight regular directions can be monitored. Therefore, the fabricated wind sensor system has great potential in wireless environmental monitoring applications.

A wormlike micellar system that undergoes a fully reversible, repeatable "sol-gel" transition upon alternative treatment with CO2 and N2 has been developed based on a C18-tailed polyamine surfactant.

No abstract

No abstract

Water wave energy is a promising renewable energy source that may alleviate the rising concerns over current resource depletion, but it is rarely exploited due to the lack of efficient energy harvesting technologies. In this work, a hybrid system with a triboelectric nanogenerator (TENG) and an electromagnetic generator (EMG) based on an optimized inner topological structure is reported to effectively harvest water wave energy. The TENG with etched polytetrafluoroethylene films and Cu electrodes utilizing the contact‐freestanding mode is designed into a cubic structure, in which the EMG is well hybridized. An integration of TENG and EMG achieves mutual compensation of their own merits, enabling the hybrid system to deliver satisfactory output over a broad range of operation frequency. The output performance of TENG with varied inner topological structures is experimentally and theoretically compared, and a concept is proposed to further clarify the energy conversion efficiency, which should be considered in designing energy harvesting devices. The influences of oscillation frequency, amplitude, and dielectric materials on the output performance of the hybrid system are comprehensively studied on different platforms. Furthermore, the optimum operation frequency ranges for TENG and EMG are concluded. The proposed hybrid nanogenerator renders an effective approach toward large‐scale blue energy harvesting over a broad frequency range.

An amidine-based polymer was prepared by combination of RAFT polymerization and "click" reaction, and the polymer undergoes a hydrophobic-hydrophilic transition upon the stimulus of CO(2).