No abstract

Human joints have respective ranges of motion and joint forces corresponding to each kind of joint; this necessitates considerations of the characteristics of human joints to fabricate wearable strain sensors conformable to the human body, and capable of precisely monitoring complex motions of the human body. In the present study, the “all textile‐based highly stretchable structure” that is capable of precisely sensing motions (folding and rotation) of the human joints (finger, wrist, elbow, spine, and knee) is fabricated by optimizing patterns (straight, blind, and zigzag) of conductive yarns employed as the conductive part of the strain sensor, and several textile substrates (braided elastic fabric, knit fabric, and woven fabric), having preferable elasticity and conformability employed for the fabrication of strain sensors suitable for human joints. In particular, the technology, enabling the prestraining of textile substrate, is exploited to fabricate a strain sensor that is capable of outputting selective signals corresponding to the folding motion of the spinal joint over a predetermined angle of motion, and the gait pattern of the wearer of the sensor, attached to his or her knee joint doing folding and rotational motions, is analyzed.

The coexistence of increasingly severe environmental concerns and bio-signal sensing systems drives the development of environmental affinity and energy harvesting materials. Chitosan is a richly sourced biodegradable material derived from crustaceans, which provides a new option for environmentally, wearable triboelectric nanogenerator (TENG). In this paper, the triboelectric performance of chitosan blends are proposed to enhance the dielectric constant by optimizing the ionic polarization and interface polarization for the first time, which fills in the blank of enhancing the output of chitosan triboelectric by systematically engineering in ionic/molecular and pH effect. Triboelectric output enhanced chitosan film in TENG shows an output voltage 3 times (18 V) higher than that of the initial film and 25 times (200 V) higher after corona charge injection. The chitosan film for wearable devices not only can be used as a unit of a triboelectric device to measure human motion signal, but also can be used as a piezoresistive sensor (ΔR/R 0 : 0 to 1.5) and an air humidity sensor (relative humidity: 20% to 90%) after mixing carbon black. The study provides a stimulating example that triboelectric nano generator/piezoresistive sensor is made from chitosan and used in the multi-modal sensing system.

Recently, wearable sensors, due to their ability to exhibit characteristics, have been appealing for health monitoring through detection of human motions and vital signals. The development of strain sensors with high sensing performance and wearability has been a great challenge to date. In this study, a textile-based strain sensor with good skin affinity was fabricated through a simple fabrication process of dip-coating 2D triaxial-braided fabrics using carbon ink and then drying. The macro crack aligned on the 2D triaxial-braided fabric with a high-density structure and good recovery force. The sensitivity of textile-based strain sensor can be enhanced due to aligned macro crack formed by prestrained fabricating process and characteristic of the 2D triaxial braided fabric with high dense structure. The optimized sensor exhibits high sensitivity (gauge factor: 128) in a strain range of 0–30%, durability (5000 cycles), washability, low hysteresis, and fast response time (90 ms). Therefore, it can be applied as a wearable sensor that can monitor human motions (large strain) and biosignals (subtle strain).

As a method to maximize the energy efficiency of triboelectric nanogenerators (TENGs), high‐voltage charge injection (HVCI) on the surface is a simple and effective method for increasing surface charge densities. In this study, positive and negative triboelectric series are controlled using a 3‐layer gradient charge‐confinement wherein the particle sizes of the mesoporous carbon spheres (mCSs) are sequentially arranged depending on the external surface area of the mCSs. In the gradient charge‐confinement layers of this study, the mCS with different sizes perform charge transport from the surface to a deep position during HVCI while mitigating the charge loss through charge confinement to induce the high space charge densities. Through this process, the output voltage—which is initially 15.2 V—is measured to be 600 V after HVCI, thus representing an increase of about 40 times. Further, to amplify the low output current, which is a disadvantage of triboelectric energy, two types of electrical energy—triboelectric and electromagnetic energy—are produced in single mechanical motion. As a result, the output current produced by the cylindrical TENG and electromagnetic generator is recorded as being 1300 times higher, increasing from 12.8 µA to 17.5 mA.

No abstract

The objective of this study is to fabricate an electrode by frictional sliding caused by a rough paper surface. The pressure exerted during drawing induces adsorption of the graphite particles by the rough paper and simultaneously reduces the surface roughness of the paper electrode. Repetitive drawing in one-way direction reduced the roughness of the paper surface, decreasing the grain boundaries of graphite. This increases the electron pathway at the electrode, thus reducing the resistance to less than 50 Ω. At the same time, repetitive drawing could confirm that unstable errors caused by the hand could help converge within a certain margin of error. We quantified the relationship between pressure and resistance when drawing on the electrode using a pencil hardness tester. In addition, the electrodes formed by repeated drawing generated a new surface grain and boundary, parallel to the drawing direction, and changed the electrode characteristics with respect to the drawing direction. The grain boundary difference based on the drawing direction was measured via a heating test of the foldable device, a sound pressure level, and laser scattering vibrometer measurements of a linear speaker. The fabricated graphite electrodes can be used in disposable foldable paper electronics because they are prepared using inexpensive materials.

No abstract