We investigated the gate bias stress effects of multilayered MoS2 field effect transistors (FETs) with a back-gated configuration. The electrical stability of the MoS2 FETs can be significantly influenced by the electrical stress type, relative sweep rate, and stress time in an ambient environment. Specifically, when a positive gate bias stress was applied to the MoS2 FET, the current of the device decreased and its threshold shifted in the positive gate bias direction. In contrast, with a negative gate bias stress, the current of the device increased and the threshold shifted in the negative gate bias direction. The gate bias stress effects were enhanced when a gate bias was applied for a longer time or when a slower sweep rate was used. These phenomena can be explained by the charge trapping due to the adsorption or desorption of oxygen and/or water on the MoS2 surface with a positive or negative gate bias, respectively, under an ambient environment. This study will be helpful in understanding the electrical-stress-induced instability of the MoS2-based electronic devices and will also give insight into the design of desirable devices for electronics applications.

We investigated the physical properties of molybdenum disulfide (MoS2) atomic crystals with a sulfur vacancy passivation after treatment with alkanethiol molecules including their electrical, Raman, and photoluminescence (PL) characteristics. MoS2, one of the transition metal dichalcogenide materials, is a promising two-dimensional semiconductor material with good physical properties. It is known that sulfur vacancies exist in MoS2, resulting in the n-type behavior of MoS2. The sulfur vacancies on the MoS2 surface tend to form covalent bonds with sulfur-containing groups. In this study, we deposited alkanethiol molecules on MoS2 field effect transistors (FETs) and then characterized the electrical properties of the devices before and after the alkanethiol treatment. We observed that the electrical characteristics of MoS2 FETs dramatically changed after the alkanethiol treatment. We also observed that the Raman and PL spectra of MoS2 films changed after the alkanethiol treatment. These effects are attributed to the thiol (-SH) end groups in alkanethiols bonding at sulfur vacancy sites, thus altering the physical properties of the MoS2. This study will help us better understand the electrical and optical properties of MoS2 and suggest a way of tailoring the properties of MoS2 by passivating a sulfur vacancy with thiol molecules.

We investigated the effects of passivation on the electrical characteristics of molybdenum disulfide (MoS(2)) field effect transistors (FETs) under nitrogen, vacuum, and oxygen environments. When the MoS(2) FETs were exposed to oxygen, the on-current decreased and the threshold voltage shifted in the positive gate bias direction as a result of electrons being trapped by the adsorbed oxygen at the MoS(2) surface. In contrast, the electrical properties of the MoS(2) FETs changed only slightly in the different environments when a passivation layer was created using polymethyl methacrylate (PMMA). Specifically, the carrier concentration of unpassivated devices was reduced to 6.5 × 10(15) cm(-2) in oxygen from 16.3 × 10(15) cm(-2) in nitrogen environment. However, in PMMA-passivated devices, the carrier concentration remained nearly unchanged in the range of 1-3 × 10(15) cm(-2) regardless of the environment. Our study suggests that surface passivation is important for MoS(2)-based electronic devices.

No abstract

One-dimensional (1D) devices are becoming the most desirable format for wearable electronic technology because they can be easily woven into electronic (e-) textile(s) with versatile functional units while maintaining their inherent features under mechanical stress. In this study, we designed 1D fiber-shaped multi-synapses comprising ferroelectric organic transistors fabricated on a 100-μm Ag wire and used them as multisynaptic channels in an e-textile neural network for wearable neuromorphic applications. The device mimics diverse synaptic functions with excellent reliability even under 6000 repeated input stimuli and mechanical bending stress. Various NOR-type textile arrays are formed simply by cross-pointing 1D synapses with Ag wires, where each output from individual synapse can be integrated and propagated without undesired leakage. Notably, the 1D multi-synapses achieved up to ~90 and ~70% recognition accuracy for MNIST and electrocardiogram patterns, respectively, even in a single-layer neural network, and almost maintained regardless of the bending conditions.

Recently, two-dimensional materials such as molybdenum disulfide (MoS2) have been extensively studied as channel materials for field effect transistors (FETs) because MoS2 has outstanding electrical properties such as a low subthreshold swing value, a high on/off ratio, and good carrier mobility. In this study, we characterized the electrical and photo-responsive properties of MoS2 FET when stacking a p-type organic copper phthalocyanine (CuPc) layer on the MoS2 surface. We observed that the threshold voltage of MoS2 FET could be controlled by stacking the CuPc layers due to a charge transfer phenomenon at the interface. Particularly, we demonstrated that CuPc/MoS2 hybrid devices exhibited high performance as a photodetector compared with the pristine MoS2 FETs, caused by more electron-hole pairs separation at the p-n interface. Furthermore, we found the optimized CuPc thickness (∼2 nm) on the MoS2 surface for the best performance as a photodetector with a photoresponsivity of ∼1.98 A W(-1), a detectivity of ∼6.11 × 10(10) Jones, and an external quantum efficiency of ∼12.57%. Our study suggests that the MoS2 vertical hybrid structure with organic material can be promising as efficient photodetecting devices and optoelectronic circuits.

In this study, a poly(e-caprolactone) (PCL)/bioactive glass (BG) nanocomposite was fabricated using BG nanofibers (BGNFs) and compared with an established composite fabricated using microscale BG particles. The BGNFs were generated using sol-gel precursors via the electrospinning process, chopped into short fibers and then incorporated into the PCL organic matrix by dissolving them in a tetrahydrofuran solvent. The biological and mechanical properties of the PCL/BGNF composites were evaluated and compared with those of PCL/BG powder (BGP). Because the PCL/BG composite containing 20 wt % BG showed the highest level of alkaline phosphatase (ALP) activity, all evaluations were performed at this concentration except for that of the ALP activity itself. In vitro cell tests using the MC3T3 cell line demonstrated the enhanced biocompatibility of the PCL/BGNF composite compared with the PCL/BGP composite. Furthermore, the PCL/BGNF composite showed a significantly higher level of bioactivity compared with the PCL/BGP composite. In addition, the results of the in vivo animal experiments using Sprague-Dawley albino rats revealed the good bone regeneration capability of the PCL/BGNF composite when implanted in a calvarial bone defect. In the result of the tensile test, the stiffness of the PCL/BG composite was further increased when the BGNFs were incorporated. These results indicate that the PCL/BGNF composite has greater bioactivity and mechanical stability when compared with the PCL/BG composite and great potential as a bone regenerative material. '

Over the past few years, attention has been focused on the therapeutic roles in designing bone scaffolds for successful repair and regeneration. Indeed, biologically dynamic events in the bone healing process involve many of the molecules and cells adherent to the scaffold. Recent bone scaffolds have been designed considering intrinsic chemical and physical factors and exogenous/extrinsic cues that induce bone regeneration. Here, we attempt to topically review the current trends and to suggest featured strategies for the design of therapeutically relevant bone scaffolds taking into account recent studies and applications.