Fluorine-contained polymers, which have been widely used in highly efficient polymer solar cells (PSCs), are rather costly due to their complicated synthesis and low yields in the preparation of components. Here, the feasibility of replacing the critical fluorine substituents in high-performance photovoltaic polymer donors with chlorine is demonstrated, and two polymeric donors, PBDB-T-2F and PBDB-T-2Cl, are synthesized and compared in parallel. The synthesis of PBDB-T-2Cl is much simpler than that of PBDB-T-2F. The two polymers have very similar optoelectronic and morphological properties, except the chlorinated polymer possess lower molecular energy levels than the fluorinated one. As a result, the PBDB-T-2Cl-based PSCs exhibit higher open circuit voltage (V ) than the PBDB-T-2F-based devices, leading to an outstanding power conversion efficiency of over 14%. This work establishes a more economical design paradigm of replacing fluorine with chlorine for preparing highly efficient polymer donors.

To make organic solar cells (OSCs) more competitive in the diverse photovoltaic cell technologies, it is very important to demonstrate that OSCs can achieve very good efficiencies and that their cost can be reduced. Here, a pair of nonfullerene small-molecule acceptors, IT-2Cl and IT-4Cl, is designed and synthesized by introducing easy-synthesis chlorine substituents onto the indacenodithieno[3,2-b]thiophene units. The unique feature of the large dipole moment of the CCl bond enhances the intermolecular charge-transfer effect between the donor-acceptor structures, and thus expands the absorption and down shifts the molecular energy levels. Meanwhile, the introduction of CCl also causes more pronounced molecular stacking, which also helps to expand the absorption spectrum. Both of the designed OSCs devices based on two acceptors can deliver a power conversion efficiency (PCE) greater than 13% when blended with a polymer donor with a low-lying highest occupied molecular orbital level. In addition, since IT-2Cl and IT-4Cl have very good compatibility, a ternary OSC device integrating these two acceptors is also fabricated and obtains a PCE greater than 14%. Chlorination demonstrates effective ability in enhancing the device performance and facile synthesis route, which both deserve further exploitation in the modification of photovoltaic materials.

Semitransparent organic solar cells (OSCs) show attractive potential in power-generating windows. However, the development of semitransparent OSCs is lagging behind opaque OSCs. Here, an ultralow-bandgap nonfullerene acceptor, "IEICO-4Cl", is designed and synthesized, whose absorption spectrum is mainly located in the near-infrared region. When IEICO-4Cl is blended with different polymer donors (J52, PBDB-T, and PTB7-Th), the colors of the blend films can be tuned from purple to blue to cyan, respectively. Traditional OSCs with a nontransparent Al electrode fabricated by J52:IEICO-4Cl, PBDB-T:IEICO-4Cl, and PTB7-Th:IEICO-4Cl yield power conversion efficiencies (PCE) of 9.65 ± 0.33%, 9.43 ± 0.13%, and 10.0 ± 0.2%, respectively. By using 15 nm Au as the electrode, semitransparent OSCs based on these three blends also show PCEs of 6.37%, 6.24%, and 6.97% with high average visible transmittance (AVT) of 35.1%, 35.7%, and 33.5%, respectively. Furthermore, via changing the thickness of Au in the OSCs, the relationship between the transmittance and efficiency is studied in detail, and an impressive PCE of 8.38% with an AVT of 25.7% is obtained, which is an outstanding value in the semitransparent OSCs.

Improving the fill factor (FF) is known as a challenging issue in organic solar cells (OSCs). Herein, a strategy of extending the conjugated area of end-group is proposed for the molecular design of acceptor-donor-acceptor (A-D-A)-type small molecule acceptor (SMA), and an indaceno[1,2-b:5,6-b']dithiophene-based SMA, namely IDTN, by end-capping with the naphthyl fused 2-(3-oxocyclopentylidene)malononitrile is synthesized. Benefiting from the π-conjugation extension by fusing two phenyls, IDTN shows stronger molecular aggregation, more ordered packing structure, thus over one order of magnitude higher electron mobility relative to its counterpart. By utilizing the fluorinated polymer (PBDB-TF) as the electron donor, the corresponding device exhibits a high efficiency of 12.2% with a record-high FF of 0.78, which is approaching the theoretical limit of OSCs. Compared with the reference molecule, such a high FF in the IDTN system can be mainly attributed to the more ordered π-π packing of acceptor aggregates, higher domain purity and symmetric carrier transport in the blend. Hence, enlarging the conjugated area of the terminal-group in these A-D-A-type SMAs is a promising approach not only for enhancing the electron mobility, but also for improving the blend morphology, and both of them are conducive to the fill-factor breakthrough.

Most of the high-performance organic solar cells are fabricated with the assistance of high-boiling-point solvent additives to optimize their charge transport properties; this has adverse effects on the OSCs’ stability and reproducibility in large-scale production. Here, we design volatilizable solid additives by considering the molecular structure feature of an acceptor–donor–acceptor-type non-fullerene acceptor. The application of solid additives can enhance the intermolecular π–π stacking of the non-fullerene acceptor and thus facilitate the charge transport properties in the active layers, leading to improved efficiencies of OSCs. Importantly, devices fabricated using volatilizable solid additives exhibit higher stability and reproducibility when compared with the OSCs processed with solvent additives. Our results not only demonstrate an approach of applying volatilizable solid additives to benefit the large-scale production of OSCs but also provide a potential direction for designing specific solid additives for different active layers.

Realizing the efficient self-propelling of small-scale condensed microdrops is very challenging but extremely important to design and develop advanced condensation heat transfer nanomaterials and devices, for example, for power generation and thermal management. Here, we present the efficient self-propelling of small-scale condensed microdrops on the surface of closely packed ZnO nanoneedles, as-synthesized by facile, rapid, and inexpensive wet chemical crystal growth followed by hydrophobic modification. Compared with flat surfaces, the nanostructured surfaces with the same low-surface-energy chemistry possess far higher time-averaged density of condensed droplets at the microscale, among which those with diameters below 10 μm occupy more than 80% of the total drop number of residual condensates. Theoretical analyses clearly reveal that this remarkable property should be ascribed to the extremely low solid-liquid adhesion of the surface nanostructure, where excess surface energy released from the coalescence of smaller condensed microdrops can be sufficient to ensure the self-propelled jumping of merged microdrops.

We report that the dropwise condensation heat transfer (DCHT) effectiveness of copper surfaces can be dramatically enhanced by in situ grown clustered ribbed-nanoneedles. Combined experiments and theoretical analyses reveal that, due to the microscopically rugged and low-adhesive nature of building blocks, the nanosamples can not only realize high-density nucleation but constrain growing condensates into suspended microdrops via the self-transport and/or self-expansion mode for subsequently self-propelled jumping, powered by coalescence-released excess surface energy. Consequently, our nanosample exhibits over 125% enhancement in DCHT coefficient. This work helps develop advanced heat-transfer materials and devices for efficient thermal management and energy utilization.

Stretchable piezoelectric nanogenerators are highly desirable for power supply of flexible electronics. Piezoelectric composite material is the most effective strategy to render piezoelectric nanogenerators stretchable. However, the generated output performance is unsatisfactory due to the low piezoelectric phase proportion. Here we demonstrate a high-performance Pb(Zr 0.52 Ti 0.48 )O 3 (PZT)-based stretchable piezoelectric nanogenerator (HSPG). The proposed HSPG exhibits excellent output performance with a power density of ∼81.25 μW/cm 3 , dozens of times higher than previously reported results. Mixing technique, instead of conventional stirring technology, is used to incorporate PZT particles into solid silicone rubber. The filler distribution homogeneity in matrix is thus remarkably improved, allowing higher filler composition. The PZT proportion in composite can be increased to 92 wt % with satisfactory stretchability of 30%. On the basis of the excellent electrical and mechanical properties, the proposed HSPG can be attached to human body to harvest body kinetic energy with multiple deformation modes. The obtained energy can be used to operate commercial electronics or be stored into a capacitor. Therefore, our HSPG has great potential application in powering flexible electronics.