Transparent wood (TW) was prepared by directly impregnating the wood cell wall and cavity with index-matched prepolymerized methyl methacrylate (MMA). In this process, lignin is retained compared with the preparation of transparent wood in the past, making the production faster and more energy-efficient. The innovation lies in that the prepared transparent wood retains the natural color and texture of the wood while transmitting light, especially under the illumination of a specific light source, which exist as the special visual effects. In order to enhance the practicality of the research and effectively expand the types of home decoration materials, six common wood species with different densities were selected in the experiment. Then the characteristics and mechanisms of wood, that is, color difference, light transmittance, microstructure, changes of chemical functional groups, and tensile strength, before and after PMMA impregnating were compared and analyzed. It is concluded that the light transmittance and mechanical properties of the wood have been improved, and a good synergistic effect between wood and PMMA has been confirmed by the analysis of scanning electron microscopy and infrared spectroscopy. The above highlights make pervious to transparent wood, which has the potential as an excellent functional decorative material.

The objective of this study is to solve the shortcomings of the current transparent bamboo veneer with a small thickness and low light transmittance by means of lamination. The delignified bamboo templates were vacuum impregnated with an epoxy resin, and the impregnated bamboo templates were laminated with the same radial texture using the viscosity of the epoxy resin to obtain multilayer transparent bamboo (MLTB). The multilayer stacking method can greatly improve the optical and mechanical properties of transparent bamboo. The transparent bamboo with a thickness of 1.2 mm and the delignified bamboo with a volume fraction of 44.8% prepared by multilayer stacking exhibited an improved total optical transmissivity of up to 78.6%, while the highest transmittance of bamboo (0.9 mm thick) without multilayer stacking treatment was only 10.4%. Compared with the single-layer transparent bamboo with a thickness of 2.1 mm, the maximum tensile strength of the seven-layer transparent bamboo was 4 times that of the single-layer transparent bamboo. Therefore, MLTB can compensate to a certain extent for the low light transmission and poor mechanical properties of single-layer transparent bamboo. Overall, MLTB shows a richer and more layered texture, which has more esthetic value. It is a kind of natural transparent material with good light transmittance and excellent mechanical properties, which has a good development prospect as a structural material in the fields of construction, household, and electronic products.

Due to its good physical properties, softened wood (SW) has been widely used in the fields of home furnishing, interior decoration, and construction, such as decorative panels, softened wood flooring, wooden bricks, and softened wood furniture. However, traditional methods of wood softening often fail to meet the requirements of enterprises for softening wood. Here, inspired by the research related to wood softening, we propose a method for directly preparing softened wood (SW) using a new type of “ionic liquid” eutectic solvent (DES) owing to its low cost, environmental friendliness, recyclability, and other advantages. To improve the adaptability of the study, a total of five types of DESs were designed and prepared, and by the microwave-assisted DES treatment of natural wood (NW), the purpose of softening wood was achieved. Then, we conducted a series of comparative analyses and performance tests on NW and SW, including microscopic images, chemical composition, color difference, and mechanical properties. The results show that the wood softened by DES has become a highly porous network structure, and partial lignin, hemicellulose, and cellulose have been removed. At the same time, different degrees of color change, lower hardness, excellent mechanical flexibility, and a compression rebound rate of up to about 90% are obtained. The above-mentioned various properties of SW provide great potential for its application in wood products.

Two common tree species of Betula alnoides (Betula) and New Zealand pine (Pinups radiata D. Don) were selected as the raw materials to prepare for the partially transparent wood (TW) in this study. Although the sample is transparent in a broad sense, it has color and pattern, so it is not absolutely colorless and transparent, and is therefore called partially transparent. For ease of interpretation, the following "partially transparent wood" is referred to as "transparent wood (TW)". The wood template (FW) was prepared by removing part of the lignin with the acid delignification method, and then the transparent wood was obtained by impregnating the wood template with a refractive-index-matched resin. The goal of this study is to achieve transparency of the wood (the light transmittance of the prepared transparent wood should be improved as much as possible) by exploring the partial delignification process of different tree species on the basis of retaining the aesthetics, texture and mechanical strength of the original wood. Therefore, in the process of removing partial lignin by the acid delignification method, the orthogonal test method was used to explore the better process conditions for the preparation of transparent wood. The tests of color difference, light transmittance, porosity, microstructure, chemical groups, mechanical strength were carried out on the wood templates and transparent wood under different experimental conditions. In addition, through the three major elements (lignin, cellulose, hemicellulose) test and orthogonal range analysis method, the influence of each process factor on the lignin removal of each tree species was obtained. It was finally obtained that the two tree species acquired the highest light transmittance at the experimental level 9 (process parameters: NaClO 2 concentration 1 wt%, 90 • C, 1.5 h); and the transparent wood retained most of the color and texture of the original wood under partial delignification up to 4.84-11.07%, while the mechanical strength with 57.76% improved and light transmittance with 14.14% higher than these properties of the original wood at most. In addition, the wood template and resin have a good synergy effect from multifaceted analysis, which showed that this kind of transparent wood has the potential to become the functional decorative material.

This experiment aims to study the performance of multilayered transparent wood (MLTW) under the condition of partial delignification, including the effect of lamination structure between layers and delignification process on the properties of MLTW. New Zealand pine (Pinus radiata D.Don) and Basswood (Tilia) were selected. The acid method was used to remove part lignin for preparing wood templates with natural wood color and texture, and then the polymer impregnated wood templates. During the lamination process, three wood templates were laminated by parallel direction (MLTW k ) or perpendicular direction (MLTW \ ) to prepare for MLTW. Under macro-and microtest, it can be seen that the laminate structure has a certain impact on the mechanical properties and light transmittance of MLTW, and MLTW can effectively reduce the anisotropy of single-layer one with the same thickness. MLTW is suitable for home decoration and structure materials and has broad application prospects.

No abstract

Transparent wood (TW) is a new material with a certain light transmission performance, which can be widely used as new energy-saving material. However, the application and development of TW are limited by material and thickness. In this work, the representative species of softwood and hardwood were selected for lamination. After chemical treatment, the lignin in natural wood was removed, and then the epoxy resin with a similar refractive index to the cell wall was impregnated in vacuum. By using the viscosity of epoxy resin itself, the single-layer materials could be effectively laminated together to prepare a new type of multilayer transparent wood (MLTW). By testing the optical properties, mechanical properties. and surface properties of MLTW materials, we found that the optical transmittance and mechanical properties can be effectively controlled and selected through the selection of materials and assembly methods. Besides, the surface properties of MLTW are mainly related to its surface material. In short, MLTW is a new composite material prepared by simple lamination at the macro level. The properties of the material can be controlled through the selection of single-layer materials and assembly methods. Compared with the traditional TW, MLTW has better performance regulation ability.

No abstract