Aqueous lithium-ion batteries may solve the safety problem associated with lithium-ion batteries that use highly toxic and flammable organic solvents, and the poor cycling life associated with commercialized aqueous rechargeable batteries such as lead-acid and nickel-metal hydride systems. But all reported aqueous lithium-ion battery systems have shown poor stability: the capacity retention is typically less than 50% after 100 cycles. Here, the stability of electrode materials in an aqueous electrolyte was extensively analysed. The negative electrodes of aqueous lithium-ion batteries in a discharged state can react with water and oxygen, resulting in capacity fading upon cycling. By eliminating oxygen, adjusting the pH values of the electrolyte and using carbon-coated electrode materials, LiTi(2)(PO(4))(3)/Li(2)SO(4)/LiFePO(4) aqueous lithium-ion batteries exhibited excellent stability with capacity retention over 90% after 1,000 cycles when being fully charged/discharged in 10 minutes and 85% after 50 cycles even at a very low current rate of 8 hours for a full charge/discharge offering an energy storage system with high safety, low cost, long cycling life and appropriate energy density.

Unlike flat sheets, crumpled paper balls have both high free volume and high compressive strength, and can tightly pack without significantly reducing the area of accessible surface. Such properties would be highly desirable for sheet-like materials such as graphene, since they tend to aggregate in solution and restack in the solid state, making their properties highly dependent on the material processing history. Here we report the synthesis of crumpled graphene balls by capillary compression in rapidly evaporating aerosol droplets. The crumpled particles are stabilized by locally folded, π-π stacked ridges as a result of plastic deformation, and do not unfold or collapse during common processing steps. In addition, they are remarkably aggregation-resistant in either solution or solid state, and remain largely intact and redispersible after chemical treatments, wet processing, annealing, and even pelletizing at high pressure. For example, upon compression at 55 MPa, the regular flat graphene sheets turn into nondispersible chunks with drastically reduced surface area by 84%, while the crumpled graphene particles can still maintain 45% of their original surface area and remain readily dispersible in common solvents. Therefore, crumpled particles could help to standardize graphene-based materials by delivering more stable properties such as high surface area and solution processability regardless of material processing history. This should greatly benefit applications using bulk quantities of graphene, such as in energy storage or conversion devices. As a proof of concept, we demonstrate that microbial fuel electrodes modified by the crumpled particles indeed outperform those modified with their flat counterparts.

Graphene is considered a promising ultracapacitor material toward high power and energy density because of its high conductivity and high surface area without pore tortuosity. However, the two-dimensional (2D) sheets tend to aggregate during the electrode fabrication process and align perpendicular to the flow direction of electrons and ions, which can reduce the available surface area and limit the electron and ion transport. This makes it hard to achieve scalable device performance as the loading level of the active material increases. Here, we report a strategy to solve these problems by transforming the 2D graphene sheet into a crumpled paper ball structure. Compared to flat or wrinkled sheets, the crumpled graphene balls can deliver much higher specific capacitance and better rate performance. More importantly, devices made with crumpled graphene balls are significantly less dependent on the electrode mass loading. Performance of graphene-based ultracapacitors can be further enhanced by using flat graphene sheets as the binder for the crumpled graphene balls, thus eliminating the need for less active binder materials.

Submicrometer-sized capsules made of Si nanoparticles wrapped by crumpled graphene shells were made by a rapid, one-step capillary-driven assembly route in aerosol droplets. Aqueous dispersion of micrometer-sized graphene oxide (GO) sheets and Si nanoparticles were nebulized to form aerosol droplets, which were passed through a preheated tube furnace. Evaporation-induced capillary force wrapped graphene (a.k.a., reduced GO) sheets around the Si particles, and heavily crumpled the shell. The folds and wrinkles in the crumpled graphene coating can accommodate the volume expansion of Si upon lithiation without fracture, and thus help to protect Si nanoparticles from excessive deposition of the insulating solid electrolyte interphase. Compared to the native Si particles, the composite capsules have greatly improved performance as Li ion battery anodes in terms of capacity, cycling stability, and Coulombic efficiency.

Graphene oxide (GO) nanocolloids-sheets with lateral dimension smaller than 100 nm-were synthesized by chemical exfoliation of graphite nanofibers, in which the graphene planes are coin-stacked along the length of the nanofibers. Since the upper size limit is predetermined by the diameter of the nanofiber precursor, the size distribution of the GO nanosheets is much more uniform than that of common GO synthesized from graphite powders. The size can be further tuned by the oxidation time. Compared to the micrometer-sized, regular GO sheets, nano GO has very similar spectroscopic characteristics and chemical properties but very different solution properties, such as surface activity and colloidal stability. Due to higher charge density originating from their higher edge-to-area ratios, aqueous GO nanocolloids are significantly more stable. Dispersions of GO nanocolloids can sustain high-speed centrifugation and remain stable even after chemical reduction, which would result in aggregates for regular GO. Therefore, nano GO can act as a better dispersing agent for insoluble materials (e.g., carbon nanotubes) in water, creating a more stable colloidal dispersion.

Porous, highly crystalline Nasicon‐type phase LiTi2(PO4)3 has been prepared by a novel poly(vinyl alcohol)‐assisted sol–gel route and coated by a uniform and continuous nanometers‐thick carbon thin film using chemical vapor deposition technology. The as‐prepared LiTi2(PO4)3 exhibits excellent electrochemical performance both in organic and aqueous electrolytes, and especially shows good cycling stability in aqueous electrolytes. An aqueous lithium‐ion battery consisting of a combination of LiMn2O4 cathode, LiTi2(PO4)3 anode, and a 1 M Li2SO4 electrolyte has been constructed. The cell delivers a capacity of 40 mA h g–1 and a specific energy of 60 W h kg–1 with an output voltage of 1.5 V based on the total weight of the active electrode materials. It also exhibits an excellent cycling stability with a capacity retention of 82 % over 200 charge/discharge cycles, which is much better than any aqueous lithium‐ion battery reported.

Graphite oxide sheet, now referred to as graphene oxide (GO), is the product of chemical oxidation and exfoliation of graphite powders that was first synthesized over a century ago. Interest in this old material has resurged in recent years, especially after the discovery of graphene, as GO is considered a promising precursor for the bulk production of graphene-based materials. GO sheets are single atomic layers that can readily extend up to tens of microns in lateral dimension. Therefore, their structure bridges the typical length scales of both chemistry and materials science. GO can be viewed as an unconventional type of soft material as it carries the characteristics of polymers, colloids, membranes, and as highlighted in this review, amphiphiles. GO has long been considered hydrophilic due to its excellent water dispersity, however, our recent work revealed that GO sheets are actually amphiphilic with an edge-to-center distribution of hydrophilic and hydrophobic domains. Thus, GO can adhere to interfaces and lower interfacial energy, acting as surfactant. This new property insight helps to better understand GO’s solution properties which can inspire novel material assembly and processing methods such as for fabricating thin films with controllable microstructures and separating GO sheets of different sizes. In addition, GO can be used as a surfactant sheet to emulsify organic solvents with water and disperse insoluble materials such as graphite and carbon nanotubes (CNTs) in water, which opens up opportunities for creating functional hybrid materials of graphene and other π-conjugated systems.

Graphite oxide (GO) has received extensive interest as a precursor for the bulk production of graphene‐based materials. Here, the highly energetic nature of GO, noted from the self‐propagating thermal deoxygenating reaction observed in solid state, is explored. Although the resulting graphene product is quite stable against combustion even in a natural gas flame, its thermal stability is significantly reduced when contaminated with potassium salt by‐products left from GO synthesis. In particular, the contaminated GO becomes highly flammable. A gentle touch with a hot soldering iron can trigger violent, catastrophic, total combustion of such GO films, which poses a serious fire hazard. This highlights the need for efficient sample purification methods. Typically, purification of GO is hindered by its tendency to gelate as the pH value increases during rinsing. A two‐step, acid–acetone washing procedure is found to be effective for suppressing gelation and thus facilitating purification. Salt‐induced flammability is alarming for the fire safety of large‐scale manufacturing, processing, and storage of GO materials. However, the energy released from the deoxygenation of GO can also be harnessed to drive new reactions for creating graphene‐based hybrid materials. Through such domino‐like reactions, graphene sheets decorated with metal and metal oxide particles are synthesized using GO as the in situ power source. Enhanced electrochemical capacitance is observed for graphene sheets loaded with RuO2 nanoparticles.