The strong and controllable chemical sensitivity of organic semiconductors (OSCs) and the amplification capability of transistors in circuits make use of OSC-based field-effect transistors compelling for chemical sensors. Analytes detected and assayed range from few-atom gas-phase molecules that may have adverse health and security implications to biomacromolecules (proteins, nucleic acids) that may be markers for physiological processes and medical conditions. This review highlights recent progress in organic field-effect transistor (OFET) chemical sensors, emphasizing advances from the past 5 years and including aspects of OSC morphology and the role of adjacent dielectrics. Design elements of the OSCs and various formats for the devices are illustrated and evaluated. Challenges associated with the present state of the art and future opportunities are also discussed. CONTENTS 4. Biomaterials Added to Organic Field-Effect Transistors 15 4.1.

CuO nanoparticles (NPs) based graphene oxide (CuO/GO) composites with different CuO NPs loading amount as well as pure CuO NPs with different hydrothermal temperatures were synthesized using a hydrothermal method. Transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and Raman spectroscopy were employed to characterize the morphology and structures of our samples. The influence of hydrothermal temperature, GO sheet, and loading amount of CuO on particle size and structure of CuO was systemically investigated. The nonenzymatic biosensing properties of CuO/GO composites and CuO NPs toward glucose were studied based on glassy carbon electrode (GCE). The sensing properties of CuO NPs were improved after loading on GO sheets. The CuO/GO composites with saturated loading of the CuO NPs exhibited the best nonenzymatic biosensing behavior. It exhibited a sensitivity of 262.52 μA mM(-1) cm(-2) to glucose with a 0.69 μM detection limit (S/N = 3) and a linear range from 2.79 μM to 2.03 mM under a working potential of +0.7 V. It also showed outstanding long term stability, good reproducibility, excellent selectivity, and accurate measurement in real serum sample. It is believed that CuO/GO composites show good promise for further application on nonenzymatic glucose biosensors.

Four p-type polymers were synthesized by modifying poly(bisdodecylquaterthiophene) (PQT12) to increase oxidizability by p-dopants. A sulfur atom is inserted between the thiophene rings and dodecyl chains, and/or 3,4-ethylenedioxy groups are appended to thiophene rings of PQT12. Doped with NOBF4, PQTS12 (with sulfur in side chains) shows a conductivity of 350 S cm, the highest reported nonionic conductivity among films made from dopant-polymer solutions. Doped with tetrafluorotetracyanoquinodimethane (F4TCNQ), PDTDE12 (with 3,4-ethylenedioxy groups on thiophene rings) shows a conductivity of 140 S cm. The converse combinations of polymer and dopant and formulations using a polymer with both the sulfur and ethylenedioxy modifications showed lower conductivities. The conductivities are stable in air without extrinsic ion contributions associated with PEDOT:PSS that cannot support sustained current or thermoelectric voltage. Efficient charge transfer, tighter π-π stacking, and strong intermolecular coupling are responsible for the conductivity. Values of nontransient Seebeck coefficient and conductivity agree with empirical modeling for materials with these levels of pure hole conductivity; the power factor compares favorably with prior p-type polymers made by the alternative process of immersion of polymer films into dopant solutions. Models and conductivities point to significant mobility increases induced by dopants on the order of 1-5 cm V s, supported by field-effect transistor studies of slightly doped samples. The thermal conductivities were in the range of 0.2-0.5 W m K, typical for conductive polymers. The results point to further enhancements that could be obtained by increasing doped polymer mobilities.

Printable and flexible electronics attract sustained attention for their low cost, easy scale up, and potential application in wearable and implantable sensors. However, they are susceptible to scratching, rupture, or other damage from bending or stretching due to their “soft” nature compared to their rigid counterparts (Si-based electronics), leading to loss of functionality. Self-healing capability is highly desirable for these “soft” electronic devices. Here, a versatile self-healing polymer blend dielectric is developed with no added salts and it is integrated into organic field transistors (OFETs) as a gate insulator material. This polymer blend exhibits an unusually high thin film capacitance (1400 nF cm −2 at 120 nm thickness and 20–100 Hz). Furthermore, it shows pronounced electrical and mechanical self-healing behavior, can serve as the gate dielectric for organic semiconductors, and can even induce healing of the conductivity of a layer coated above it together with the process of healing itself. Based on these attractive properties, we developed a self-healable, low-voltage operable, printed, and flexible OFET for the first time, showing promise for vapor sensing as well as conventional OFET applications.