CuO nanoparticles (NPs) based graphene oxide (CuO/GO) composites with different CuO NPs loading amount as well as pure CuO NPs with different hydrothermal temperatures were synthesized using a hydrothermal method. Transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and Raman spectroscopy were employed to characterize the morphology and structures of our samples. The influence of hydrothermal temperature, GO sheet, and loading amount of CuO on particle size and structure of CuO was systemically investigated. The nonenzymatic biosensing properties of CuO/GO composites and CuO NPs toward glucose were studied based on glassy carbon electrode (GCE). The sensing properties of CuO NPs were improved after loading on GO sheets. The CuO/GO composites with saturated loading of the CuO NPs exhibited the best nonenzymatic biosensing behavior. It exhibited a sensitivity of 262.52 μA mM(-1) cm(-2) to glucose with a 0.69 μM detection limit (S/N = 3) and a linear range from 2.79 μM to 2.03 mM under a working potential of +0.7 V. It also showed outstanding long term stability, good reproducibility, excellent selectivity, and accurate measurement in real serum sample. It is believed that CuO/GO composites show good promise for further application on nonenzymatic glucose biosensors.

Three-dimensional (3D) porous ZnO–CuO hierarchical nanocomposites (HNCs) nonenzymatic glucose electrodes with different thicknesses were fabricated by coelectrospinning and compared with 3D mixed ZnO/CuO nanowires (NWs) and pure CuO NWs electrodes. The structural characterization revealed that the ZnO–CuO HNCs were composed of the ZnO and CuO mixed NWs trunk (~200 nm), whose outer surface was attached with small CuO nanoparticles (NPs). Moreover, a good synergetic effect between CuO and ZnO was confirmed. The nonenzymatic biosensing properties of as prepared 3D porous electrodes based on fluorine doped tin oxide (FTO) were studied and the results indicated that the sensing properties of 3D porous ZnO–CuO HNCs electrodes were significantly improved and depended strongly on the thickness of the HNCs. At an applied potential of + 0.7 V, the optimum ZnO–CuO HNCs electrode presented a high sensitivity of 3066.4 μAmM−1cm−2, the linear range up to 1.6 mM, and low practical detection limit of 0.21 μM. It also showed outstanding long term stability, good reproducibility, excellent selectivity and accurate measurement in real serum sample. The formation of special hierarchical heterojunction and the well-constructed 3D structure were the main reasons for the enhanced nonenzymatic biosensing behavior.

A series of In2O3/Au nanorods (NRs) were fabricated and characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), X–ray diffractometer (XRD) and X–ray photoelectron spectroscopy (XPS). The length to diameter ratios of In2O3/Au NRs was periodically modulated in the range of 2.9–4.5 through controlling the initial content of indium salt and reaction time. Their gas sensing properties to volatile organic compounds (VOCs) were carefully studied and then applied in exhaled breath detection. The results demonstrate that In2O3/Au NRs gas sensor can effectively detect acetone at 250 °C and ethanol at 400 °C. The corresponding actual detection limit is as low as 0.1 ppm to acetone and 0.05 ppm to ethanol, respectively. Moreover, by using humidity compensation method, In2O3/Au NRs gas sensor can clearly distinguish the acetone and ethanol biomarkers in human breath. The main reason of the enhanced gas sensing properties was attributed to the “spillover effects” between Au and In2O3 NRs. The excellent sensing performance indicates that In2O3/Au NRs is a promising functional material to actual application in monitoring and detecting diabetes and safe driving area in a noninvasive and more accurate way.

Hybrid capacitors exhibit promise to bridge the gap between rechargeable high-energy density batteries and high-power density supercapacitors. This separation is due to sluggish ion/electron diffusion and inferior structural stability of battery-type materials. Here, a topochemistry-driven method for constructing expanded 2D rhenium selenide intercalated by nitrogen-doped carbon hybrid (E-ReSe 2 @INC) with a strong-coupled interface and weak van der Waals forces, is proposed. X-ray absorption spectroscopy analysis dynamically tracks the transformation from ReO into ReC bonds. The bridging bonds act as electron transport channels to enable improved conductivity and accelerated reaction kinetics. The expanded interlayer-spacing of ReSe 2 layer by INC facilitates ion diffusion and ensures structural stability. As expected, the E-ReSe 2 @INC achieves an improved rate capability (252.5 mAh g −1 at 20 A g −1 ) and long-term cyclability (89.6% over 3500 cycles). Moreover, theoretical simulations reveal the favorable Na + storage kinetics can be ascribed to its low bonding energy of −0.06 eV and diffusion barrier of 0.08 eV for sodium ions. Additionally, it is demonstrated that 3D printed sodium-ion hybrid capacitors deliver high energies/power densities of 81.4 Wh kg −1 /0.32 mWh cm −2 and 9992.1 W kg −1 /38.76 mW cm −2 , as well as applicability in a wide temperature range.

There has been great progress in the development of fluorescence biosensors based on quantum dots (QDs) for the detection of lead ions. However, most methods are detecting lead ions in aqueous solution rather than in human serum due to the influence of protein autofluorescence in serum excited by visible light. Thus, we developed a novel fluorescence resonance energy transfer (FRET) biosensor by choosing the upconversion NaYF4:Yb(3+)/Tm(3+) nanoparticles as the energy donor and the CdTe QDs as the energy acceptor for lead ion detection. It is the first near infrared (NIR)-excited fluorescent probe for determination of lead ions in serum that is capable of overcoming self-luminescence from serum excitation with visible light. The sensor also shows high selectivity, a low detection limit (80 nm) and good linear Stern-Volmer characteristics (R = 0.996), both in the buffer and serum. This biosensor has great potential for versatile applications in lead ion detection in biological and analytical fields.

In this work, we present a novel ascorbic acid (AA) sensor applied to the detection of AA in human sera and pharmaceuticals. A series of Au nanoparticles (NPs) and graphene oxide sheets (Au NP/GO) composites were successfully synthesized by reduction of gold (III) using sodium citrate. Then the Au NP/GO composites were used to construct nonenzymatic electrodes in practical AA measurement. The electrode that has the best performance presents attractive analytical features, such as a low working potential of +0.15 V, a high sensitivity of 101.86 μA mM−1 cm−2 to AA, a low detection limit of 100 nM, good reproducibility and excellent selectivity. And more,it was also employed to accurately and practically detect AA in human serum and clinical vitamin C tablet with the existence of some food additive. The enhanced AA electrochemical properties of the Au NP/GO modified electrode in our work can be attributed to the improvement of electroactive surface area of Au NPs and the synergistic effect from the combination of Au NPs and GO sheets. This work shows that the Au NP/GO/GCEs hold the prospect for sensitive and selective determination of AA in practical clinical application.

No abstract

In this present work, we proposed a colorimetric strategy for simultaneous detection of histidine and cysteine based on G-quadruplex-Cu(II) metalloenzyme for the first time. Because of the adding of histidine or cysteine, the formation of G-quadruplex-Cu(II) metalloenzyme will be disturbed, thus the catalytic activity to TMB-H2O2 reaction is inversely proportional to the concentration of histidine or cysteine. With this strategy, the limit of detection in experimental measurement for histidine and cysteine is 10 nM and 5 nM, respectively, which are both lower than previous colorimetric arrays. With the help of NEM, cysteine is alkylated and the reaction between Cu(2+) is inhibited, so the selectivity can also be guaranteed. The cost is quite low since the developed array is label free and enzyme free by using low-cost DNA and Cu(2+). More importantly, the colorimetric detection operation is very simple without any further modification process.