No abstract

No abstract

No abstract

Selective laser melting (SLM) is emerging as a versatile process for fabricating different metal components with acceptable mechanical properties and geometrical accuracy. The process has been used in the manufacturing of several parts (e.g., aerospace or biomedical components), and offers the capability to tailor the performance of several surface and mechanical properties. In this work, permeability properties and surface roughness of stainless steel (SS316L) surfaces were evaluated through experimentation with three different laser scanning patterns (chessboard, meander, and stripe), and different sloping angles between the fabricated surface and the laser beam incident on the process. Results showed that for each scanning pattern, the roughness decreased as the sloping angle increased consistently in all experimental trials. Furthermore, in the case of the permeability evaluation, the manufactured surfaces showed changes in properties for each series of experiments performed with different scanning patterns. The chessboard pattern showed a change of 67 • to 107 • in contact angle, while the meander and stripe patterns showed a variation in contact angle in a range of 65 • to 85 • . The different scanning strategies in the SLM process resulted in an alternative method for surface enhancement with different hydrophobicity properties, valuable for designing the most appropriate permeability characteristics for specific applications.

The interplay between a prosthetic and tissue represents an important factor for the fixation of orthopedic implants. Laser texturing tests and electropolishing were performed on two materials used in the fabrication of medical devices, i.e., CoCr and Ti6Al4V-ELI alloys. The material surface was textured with a diode-pumped solid state (DPSS) laser and its effect on the surface quality and material modification, under different combinations of laser power and marking speed, were investigated. Our results indicate that an increment of energy per unit length causes an incremental trend in surface roughness parameters. Additionally, phase transformation on the surface of both alloys was achieved. Chemical analysis by energy dispersive X-ray spectrometer (EDX) shows the formation of (Co(Cr,Mo)) phase and the M23C6 precipitate on the CoCr surface; while quantitative analysis of the X-ray diffractometer (XRD) results demonstrates the oxidation of the Ti alloy with the formation of Ti2O and Ti6O from the reduction of the α-Ti phase. The behaviors were both related with an increase of the energy per unit length. Control of the final surface roughness was achieved by an electropolishing post-treatment, minimizing the as-treated values. After polishing, a reduction of surface roughness parameters was obtained in a range between 3% and 44%, while no changes in chemical composition or present phases were observed.

The metallurgical understanding of the deformation processes during the fabrication of non-oriented electrical steels plays a key role in improving their final properties. Texture control and optimization is critical in these steels for the enhancement of their magnetic properties. The aim of the present work is to study the texture evolution of six non-oriented experimental silicon steel grades during hot rolling. These steels were low carbon steel with a silicon content from 0.5 to 3.0 wt%. The first rolling schedule was performed in the austenitic (¿-Fe) region for the steel with a 0.5 wt% of silicon content, while the 1.0 wt% silicon steel was rolled in the two-phase (a+¿) region. Steels with higher silicon content were rolled in the ferritic (a-Fe) region. The second rolling schedule was performed in the a-Fe region. Samples of each stage were analyzed by means of Electron Backscatter Diffraction (EBSD). Findings showed that the texture was random and heterogeneous in all samples after 60% of rolling reduction, which is due to the low deformation applied during rolling. After the second rolling program, localized deformation and substructured grains near to surface were observed in all samples. The Goss {110}<001>texture-component was found in the 0.5 and 1.0 wt.-%silicon steels. This is due to the thermomechanical conditions and the corresponding hot band microstructure obtained after the first program. Moreover, the a<110>//RD and the ¿ <111>//ND fiber components of the texture presented a considerable increment as the silicon content increases. Future research to be published soon will be related to the texture evolution during the cold-work rolling process.Peer ReviewedPostprint (author's final draft

The understanding of dimensional variations produced by laser powder bed fusion is critical in components with small features and with dimensions close to the inherent limits of the process. In this context, two reference geometries were used: (a) straight walls to quantify dimensional relative error for small features and (b) a latticed neck region of a fatigued specimen (cubic and hexagonal cell design, with design strut sizes of 250 µm, 500 µm, and 1000 µm in cell size). Samples were fabricated out of AISI 316L stainless steel powder with different building orientations. The metrology techniques used were the following: focus variation microscopy, optical microscopy and micro-computed tomography. The straight wall characterization shows that built orientation does not influence dimensional relative error for walls with less than 750 µm. Acceptable dimensional relative errors (~ 2% to ~ 15%) are achieved only in walls with 750 µm in width of more. For lattice structures, the fine struts (250 µm) show a significant level of dimensional relative error (~ 5% to ~ 25%). This additive manufacturing process delivers more consistent dimensions for coarse struts (500 µm), with relative errors between ~ 2% and ~ 4%. All metrology techniques showed the same trends in terms of capturing the dimensional variations for fine and coarse struts.