We report a novel approach whereby cross-linked polybutadiene (PB) networks can be depolymerized in situ based on thermally activated alkene metathesis. A commercially available latent Ru catalyst, HeatMet, was compared to the common second-generation Hoveyda–Grubbs catalyst, HG2, in the metathetic depolymerization of PB. HeatMet was found to possess exceptional stability and negligible activity toward PB under ambient conditions, in solution and in bulk. This enabled cross-linked networks to be prepared containing homogeneously distributed Ru catalyst. The dynamic mechanical properties of networks containing HeatMet and cross-linked using alcohol–isocyanate or thiol–ene chemistry were evaluated during cross-linking and post-cross-linking under isothermal and nonisothermal heating. In both cases, above minimum catalyst loadings ranging from 0.004 to 0.024 mol %, the networks exhibited rapid degelation into a soluble oil upon heating to 100 °C. At these temperatures, extensive depolymerization of the PB segments through ring-closing metathesis of 1,4/1,2 diads by the activated HeatMet introduced network defects in significantly greater proportion than the original number of cross-links. The in situ depolymerization of cross-linked PB networks through latent catalysis, as described here, may enable facile disposal and recycling of PB encapsulants and adhesives, among other applications.

The large, directional stimuli-response of aligned liquid crystalline elastomers (LCEs) could enable functional utility in robotics, medicine, consumer goods, and photonics. The alignment of LCEs has historically been realized via mechanical alignment of a two-stage reaction. Recent reports widely utilize chain extension reactions of liquid crystal monomers (LCM) to form LCEs that are subject to either surface-enforced or mechanical alignment. Here, we prepare LCEs that contain intra-mesogenic supramolecular bonds synthesized via direct free-radical chain transfer photopolymerization processible by a distinctive mechanical alignment mechanism. The LCEs were prepared by the polymerization of a benzoic acid monomer (11OBA), which dimerized to form a liquid crystal monomer, with a diacrylate LCM (C6M). The incorporation of the intra-mesogenic hydrogen bonds increases the achievable nematic order from mechanical programming. Accordingly, LCEs prepared with larger 11OBA concentration exhibit higher magnitude thermomechanical strain values when compared to a LCE containing only covalent bonds. These LCEs can be reprogrammed with heat to return the aligned film to the polydomain state. The LCE can then be subsequently programmed to orient in a different direction. The facile preparation of (re)programmable LCEs with supramolecular bonds opens new avenues for the implementation of these materials as shape deployable elements.

Liquid crystalline elastomers (LCE) are thermally cyclable, compliant actuators with compelling mechanical properties. The large and programmable deformation of LCE has led to numerous functional examinations spanning optics, medical devices, and robotics. A well-established method to prepare complex LCE actuators is to utilize surface-enforced photoalignment. Herein, a facile and scalable approach is reported to circumvent the physical limits of surface-enforced alignment (e.g., samples that are 50 μm or less) to amplify the achievable force output in LCE. Applying an approach termed direct layering, the thermomechanical response of LCE elements prepared with +1 disclination patterns in a range of compositions and thicknesses is contrasted. The design and preparation of +1 disclination patterns and arrays is explored to assess the contribution of sample geometry and overlap to deformation and force output. The methodology detailed in this contribution allows for the preparation of elements ≈1 mm in thickness that are capable of actuating large objects. Furthermore, the fabrication of these elements uniquely enables the realization of mechanical instabilities to hasten the actuation rate in response to thermal change and to enable leaping.

This communication describes a novel series of linear and crosslinked polyurethanes (PUs) and their selective depolymerization under mild conditions. Two unique polyols are synthesized bearing unsaturated units in a configuration designed to favor ring‐closing metathesis (RCM) to five‐ and six‐membered cycloalkenes. These polyols are co‐polymerized with toluene diisocyanate to generate linear PUs and trifunctional hexamethylene‐ and diphenylmethane‐based isocyanates to generate crosslinked PUs. The polyol design is such that the RCM reaction cleaves the backbone of the polymer chain. Upon exposure to dilute solutions of Grubbs’ catalyst under ambient conditions, the PUs are rapidly depolymerized to low molecular weight, soluble products bearing vinyl and cycloalkene functionalities. These functionalities enable further re‐polymerization by traditional strategies for polymerization of double bonds. It is anticipated that this general approach can be expanded to develop a range of chemically recyclable condensation polymers that are readily depolymerized by orthogonal metathesis chemistry.

Inside Cover: In article number 2000571 by Brad H. Jones and coworkers, linear and crosslinked polyurethanes are prepared from traditional isocyanates and new polyols containing unsaturated moieties designed to favor ring‐closing olefin metathesis and concomitant cleavage of the molecule. These polyurethanes are found to be efficiently depolymerized upon exposure to second generation Hoveyda–Grubbs catalyst under ambient conditions. The depolymerization products are multi‐vinyl/cycloalkene species that can be re‐polymerized.