A high frequency experiment was conducted in the Woods Hole Harbor in Massachusetts to evaluate the effectiveness of Doppler sonar for discriminating targets from reverberation. Using a pulsed linear frequency modulated signal, one finds that the matched filtered outputs are filled with high-level discrete backscattered returns, referred to as clutter, which are often confused with the target echo. The high level non-target returns have an amplitude distribution that is heavy-tailed. Using a Doppler-sensitive binary-phase-shift-keying signal coded with an m-sequence, the target echo and clutter can be separated by Doppler and delay, and tracked using the Doppler spectrogram (Dopplergram). The Doppler filtered time series show a background reverberation with a Rayleigh-like amplitude distribution, with an improved signal-to-(peak) reverberation ratio compared with that without Doppler filtering. The reduced reverberation level with Doppler processing decreases the probability of false alarm (Pfa) for a given threshold level. Conversely, for a given Pfa, the higher signal-to-(peak) reverberation ratio implies a higher probability of detection. Transmission loss measurement was conducted to estimate some of the system parameters, e.g., the source level and target strength relative to the noise level.
Preliminary results are presented from a recent experiment carried out at the NUWC Seneca Lake test facility and designed to investigate the scattering properties of bubble clouds produced in fresh water in the absence of boundaries and under known propagation conditions.The test range consisted of both conventional and parametric sources, conventional receivers, and a transient bubbler that was submerged to 91 m. The cloud possessed an elongated teardrop shape (lengthm 1.4 m, diameters0.5 m) with a void fraction of 0.25% and a mean bubble radius of 1.5 mm, which corresponds to a single-bubble resonance frequency of 6.6 kHz at depth. Backscatter target strengths were measured for frequencies ranging from 300 Hz to 14 kHz. These measurements revealed high target strengths (up to + I dB) and distinctive peaks in the spectrum at 450 Hz, and 1.3, 3.0, 6.5, and 11 kHz. The low-frequency results are consistent with calculations (based on the theory of collective bubble oscillations) of the resonance frequency and target strength of a comparably sized, spherical bubble cloud. Certain features of the high-frequency backscatter data are consistent with single-bubble resonance scattering. These preliminary results are consistent with the notion that, at low frequencies, the scattering characteristics of a bubble cloud are determined, not by the bubble sizes and number density, but rather by the free-gas volume fraction and the length scales of the cloud proper.
Distributed underwater sensors are expected to provide oceanographic monitoring over large areas. As fabrication technology advances, low cost sensors will be available for many uses. The sensors communicate to each other and are networked using acoustic communications. This paper first studies the performance of such systems for current measurements using tomographic inversion approaches to compare with that of a conventional system which distributes the sensors on the periphery of the area of interest. It then proposes two simple signal processing methods for ocean current mapping (using distributed networked sensors) aimed at real-time in-buoy processing. Tomographic inversion generally requires solving a challenging high dimensional inverse problem, involving substantial computations. Given distributed sensors, currents can be constructed locally based on data from neighboring sensors. It is shown using simulated data that similar results are obtained using distributed processing as using conventional tomographic approaches. The advantage for distributed systems is that by increasing the number of nodes, one gains a much more improved performance. Furthermore, distributed systems use much less energy than a conventional tomographic system for the same area coverage. Experimental data from an acoustic communication and networking experiment are used to demonstrate the feasibility of acoustic current mapping.
Acoustic data from the Canada Basin Acoustic Propagation Experiment are discussed. These recordings were obtained under seasonally varying sea ice to the north of Alaska during a period of 154 days. They contain signals from sources that were deployed at ranges of 17.5, 29.6, and 237.8 km and ambient sounds from marine mammals and ice-related events. After the area was covered with ice, the amplitude of receptions from the most distant source gradually decreased as scattering features on the underside of the ice developed during fracturing, drifting, ridging, and rafting events. Improvements are presented for an Arctic acoustic model that is based on the parabolic equation method, and the approach is applied to a problem in which variable ice thickness acts as a loss mechanism by scattering energy out of the waveguide. Some of the recordings have a harmonic signature that is believed to be associated with the resonances of ice floes rubbing together, but variations in the harmonics over short time scales cannot be explained in terms of the resonances of an isolated floe. This behavior may be related to the coupling of vibrations at contact points that vary during the relative motions of floes.
Significant acoustic travel-time variability and frequency shifts of acoustic intensity level curves in broadband signal spectrograms were measured in the East China Sea during the summer of 2008. The broadband pulses (270-330 Hz) were transmitted from a fixed source and received at a bottomed horizontal array, located at the 33 km range. The acoustic intensity level curves of the received signals indicate regular frequency shifts that are well correlated with the measured internal tides. Similarly, regular travel-time shifts of the acoustic mode arrivals correlate well with the barotropic tides and can be explained by tidal currents along the acoustic propagation track. These observations indicate the potential of monitoring internal tides and tidal currents using low-frequency acoustic signals propagating at long ranges.
This paper proposes a method for ocean current mapping using distributed networked sensors and presents preliminary experimental results by this approach. Conventional acoustic tomography uses the acoustic sensors distributed on the periphery of an area of interest. Environmental reconstruction requires solving a challenging high dimensional inverse problem, typically requiring substantial computational effort. Given distributed sensors, currents can be constructed locally based on data from neighboring sensors. An acoustic communication and networking experiment was conducted near the Sizihwan Bay in Kaohsiung, Taiwan, in May 2011. The collected communication signals are used to demonstrate the proposed method for inverting the currents as a function of space and time. The procedure is simple and can be implemented in real-time using in-buoy processing. General TermsExperimentation
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.