Lithium transition metal phosphates have become of great interest as storage cathodes for rechargeable lithium batteries because of their high energy density, low raw materials cost, environmental friendliness and safety. Their key limitation has been extremely low electronic conductivity, until now believed to be intrinsic to this family of compounds. Here we show that controlled cation non-stoichiometry combined with solid-solution doping by metals supervalent to Li+ increases the electronic conductivity of LiFePO4 by a factor of approximately 10(8). The resulting materials show near-theoretical energy density at low charge/discharge rates, and retain significant capacity with little polarization at rates as high as 6,000 mA x g(-1). In a conventional cell design, they may allow development of lithium batteries with the highest power density yet.

Interfaces between organic electron-donating (D) and electron-accepting (A) materials have the ability to generate charge carriers on illumination. Efficient organic solar cells require a high yield for this process, combined with a minimum of energy losses. Here, we investigate the role of the lowest energy emissive interfacial charge-transfer state (CT1) in the charge generation process. We measure the quantum yield and the electric field dependence of charge generation on excitation of the charge-transfer (CT) state manifold via weakly allowed, low-energy optical transitions. For a wide range of photovoltaic devices based on polymer:fullerene, small-molecule:C60 and polymer:polymer blends, our study reveals that the internal quantum efficiency (IQE) is essentially independent of whether or not D, A or CT states with an energy higher than that of CT1 are excited. The best materials systems show an IQE higher than 90% without the need for excess electronic or vibrational energy.

Here we report on a novel substrate, nanopaper, made of cellulose nanofibrils, an earth abundant material.Compared with regular paper substrates, nanopaper shows superior optical properties. We have carried out the first study on the optical properties of nanopaper substrates. Since the size of the nanofibrils is much less than the wavelength of visible light, nanopaper is highly transparent with large light scattering in the forward direction. Successful depositions of transparent and conductive materials including tin-doped indium oxide, carbon nanotubes and silver nanowires have been achieved on nanopaper substrates, opening up a wide range of applications in optoelectronics such as displays, touch screens and interactive paper. We have also successfully demonstrated an organic solar cell on the novel substrate. Broader contextWood ber cellulose has been used for more than 2000 years as an ingredient for making paper. The cellulose paper that we see in our everyday lives consists of bers with diameters of tens of micrometers. Using chemical or enzymatic pretreatments followed by high-pressure homogenization, the micrometer-sized cellulose bers can be disintegrated into nanobrillated cellulose (NFC) with a diameter of around 10-20 nm and a length of 2 mm. By compressing the NFC pulp with the right composition in a sheet-former, highly transparent nanocellulose paper can be produced. The nanocellulose paper has large light scattering in the forward direction, which is very useful for solar cell applications. The nanocellulose paper can be coated with a wide variety of conductive materials, such as carbon nanotubes, silver nanowires and tin-doped indium oxide (ITO), to produce transparent conductive paper. By depositing a thin layer of ITO, the conductive nanocellulose paper can be used as a substrate for making organic solar cells.

We present the synthesis and device characterization of new hole transport materials (HTMs) for application in solid-state dye-sensitized solar cells (ssDSSCs). In addition to possessing electrical properties well suited for ssDSSCs, these new HTMs have low glass transition temperatures, low melting points, and high solubility, which make them promising candidates for increased pore filling into mesoporous titania films. Using standard device fabrication methods and Z907 as the sensitizing dye, power conversion efficiencies (PCE) of 2.94% in 2-μm-thick cells were achieved, rivaling the PCE obtained by control devices using the state-of-the-art HTM spiro-OMeTAD. In 6-μm-thick cells, the device performance is shown to be higher than that obtained using spiro-OMeTAD, making these new HTMs promising for preparing high-efficiency ssDSSCs.

A new series of electron-deficient molecules based on a central benzothiadiazole moiety flanked with vinylimides has been synthesized via Heck chemistry and used in solution-processed organic photovoltaics (OPV). Two new compounds, 4,7bis(4-(N-hexyl-phthalimide)vinyl)benzo[c]1,2,5-thiadiazole (PI-BT) and 4,7-bis(4-(N-hexylnaphthalimide)vinyl)benzo[c]1,2,5-thiadiazole (NI-BT), show significantly different behaviors in bulk heterojunction (BHJ) solar cells using poly(3-hexylthiophene) (P3HT) as the electron donor. Two-dimensional grazing incidence X-ray scattering (2D GIXS) experiments demonstrate that PI-BT shows significant crystallization in spin-coated thin films, whereas NI-BT does not. Density functional theory (DFT) calculations predict that while PI-BT maintains a planar structure in the ground state, steric interactions cause a twist in the NI-BT molecule, likely preventing significant crystallization. In BHJ solar cells with P3HT as donor, PI-BT devices achieved a large open-circuit voltage of 0.96 V and a maximum device powerconversion efficiency of 2.54%, whereas NI-BT containing devices only achieved 0.1% power-conversion efficiency.