Arrays of sub-wavelength holes (nanoholes) in gold films were used as a substrate for enhanced fluorescence spectroscopy. Seven arrays of nanoholes with distinct periodicities (distances between the holes) were fabricated. The arrays were then spin-coated with polystyrene films containing different concentrations of the fluorescent dye oxazine 720. The dye was excited via resonant extraordinary transmission of the laser source through the nanoholes. Enhanced fluorescence was observed when the geometric characteristics of the arrays allowed for an enhancement in the transmitted excitation. This enhancement occurred via surface plasmon excitation by the laser and a consequential increase in the local electromagnetic field in a sub-wavelength region at the metal-film interface. It was demonstrated that the sensitivity of the fluorescence measurement (change in signal vs change in dye concentration in the polymer film) is significantly larger at the surface plasmon resonance conditions than that obtained from equivalent films on glass substrates. Enhancement factors for the fluorescence emission were calculated for each array, with a maximum enhancement of close to 2 orders of magnitude as compared to the emission of films on glass. The results presented here indicate that arrays of nanoholes are interesting substrates for the development of fluorescence sensors based on surface plasmon resonance, as they provide a platform that allows both spatial confinement and enhancement of excitation light. Moreover, the collinear characteristics of the present optical setup, due to the resonant extraordinary transmission through the nanohole arrays, are more conducive to miniaturization and chip integration than more traditional experimental geometries.

Infertility is a growing global health issue with far-reaching socioeconomic implications. A downward trend in male fertility highlights the acute need for affordable and accessible diagnosis and treatment. Assisted reproductive technologies are effective in treating male infertility, but their success rate has plateaued at ∼33% per cycle. Many emerging opportunities exist for microfluidics - a mature technology in other biomedical areas - in male infertility diagnosis and treatment, and promising microfluidic approaches are under investigation for addressing male infertility. Microfluidic approaches can improve our fundamental understanding of sperm motion, and developments in microfluidic devices that use microfabrication and sperm behaviour can aid semen analysis and sperm selection. Many burgeoning possibilities exist for engineers, biologists, and clinicians to improve current practices for infertility diagnosis and treatment. The most promising avenues have the potential to improve medical practice, moving innovations from research laboratories to clinics and patients in the near future.

No abstract

We compare the microfluidic manufacturing of polycaprolactone-block-poly(ethylene oxide) (PCL-b-PEO) nanoparticles (NPs) in a single-phase staggered herringbone (SHB) mixer and in a two-phase gas-liquid segmented mixer. NPs generated from two different copolymer compositions in both reactors and at three different flow rates, along with NPs generated using a conventional bulk method, are compared with respect to morphologies, dimensions, and internal crystallinities. Our work, the first direct comparison between alternate microfluidic NP synthesis methods, shows three key findings: (i) NP morphologies and dimensions produced in the bulk are different from those produced in a microfluidic mixer, whereas NP crystallinities produced in the bulk and in the SHB mixer are similar; (ii) NP morphologies, dimensions, and crystallinities produced in the single-phase SHB and two-phase mixers at the lowest flow rate are similar; and (iii) NP morphologies, dimensions, and crystallinities change with flow rate in the two-phase mixer but not in the single-phase SHB mixer. These findings provide new insights into the relative roles of mixing and shear in the formation and flow-directed processing of polymeric NPs in microfluidics, informing future reactor designs for manufacturing NPs of low polydispersity and controlled multiscale structure and function.

No abstract

The coupling of semiconductor quantum dots (QDs) to the surface plasmon (SP) modes of nanohole arrays in a metal film was demonstrated for the first time, showing enhancement in the spontaneous emission by 2 orders of magnitude. The SP-enhanced transmission resonances of the nanohole arrays were tuned around the photoluminescence (PL) peak of polystyrene-b-poly(acrylic acid) (PS-b-PAA)-stabilized cadmium sulfide (CdS) quantum dots (QDs) in contact with the arrays. As a result the overall PL from the SP-QD system was enhanced by 2 orders of magnitude, even after excluding the enhanced transmission of the nanohole array without the QDs. The maximum enhancement occurred when the resonance from the nanohole array matched the QD PL spectrum. Time-resolved PL measurements were used to estimate the relative contribution of different physical mechanisms to the enhanced spontaneous emission. The increased spontaneous emission in the SP-QD system is promising for prospective plasmonic light-emitting devices incorporating QDs.

Microfluidic systems that leverage unique micro-scale phenomena have been developed to provide rapid, accurate and robust analysis, predominantly for biomedical applications. These attributes, in addition to the ability to access high temperatures and pressures, have motivated recent expanded applications in phase measurements relevant to industrial CO, oil and gas applications. We here present a comprehensive review of this exciting new field, separating microfluidic and nanofluidic approaches. Microfluidics is practical, and provides similar phase properties analysis to established bulk methods with advantages in speed, control and sample size. Nanofluidic phase behaviour can deviate from bulk measurements, which is of particular relevance to emerging unconventional oil and gas production from nanoporous shale. In short, microfluidics offers a practical, compelling replacement of current bulk phase measurement systems, whereas nanofluidics is not practical, but uniquely provides insight into phase change phenomena at nanoscales. Challenges, trends and opportunities for phase measurements at both scales are highlighted.

Microalgal biofuel is an emerging sustainable energy resource. Photosynthetic growth is heavily dependent on irradiance, therefore photobioreactor design optimization requires comprehensive screening of irradiance variables, such as intensity, time variance and spectral composition. Here we present a microfluidic irradiance assay which leverages liquid crystal display technology to provide multiplexed screening of irradiance conditions on growth. An array of 238 microreactors are operated in parallel with identical chemical environments. The approach is demonstrated by performing three irradiance assays. The first assay evaluates the effect of intensity on growth, quantifying saturating intensity. The second assay quantifies the influence of time-varied intensity and the threshold frequency for growth. Lastly, the coupled influence of red-blue spectral composition and intensity is assessed. Each multiplexed assay is completed within three days. In contrast, completing the same number of experiments using conventional incubation flasks would require several years. Not only does our approach enable more rapid screening, but the short optical path avoids self-shading issues inherent to flask based systems.