Low roll-off angle, high impalement pressure, and mechanical robustness are key requirements for super-liquid-repellent surfaces to realize their potential in applications ranging from gas exchange membranes to protective and self-cleaning materials. Achieving these properties is still a challenge with superamphiphobic surfaces, which can repel both water and low-surface-tension liquids. In addition, fabrication procedures of superamphiphobic surfaces are typically slow and expensive. Here, by making use of liquid flame spray, a silicon dioxide-titanium dioxide nanostructured coating is fabricated at a high velocity up to 0.8 m s . After fluorosilanization, the coating is superamphiphobic with excellent transparency and an extremely low roll-off angle; 10 µL drops of n-hexadecane roll off the surface at inclination angles even below 1°. Falling drops bounce off when impacting from a height of 50 cm, demonstrating the high impalement pressure of the coating. The extraordinary properties are due to a pronounced hierarchical nanotexture of the coating.

Paper-based devices provide an alternative technology for simple, low-cost, portable, and disposable diagnostic tools for many applications, including clinical diagnosis, food quality control, and environmental monitoring. In this study we report a two-step fabrication process for creating two-dimensional microfluidic channels to move liquids on a hydrophobized paper surface. A highly hydrophobic surface was created on paper by TiO2 nanoparticle coating using a high-speed, roll-to-roll liquid flame spray technique. The hydrophilic pattern was then generated by UV irradiation through a photomask utilizing the photocatalytic property of TiO2. The flow dynamics of five model liquids with differing surface tensions 48-72 mN·m(-1) and viscosities 1-15 mN·m(-2) was studied. The results show that the liquid front (l) in a channel advances in time (t) according to the power law l=Zt0.5 (Z is an empirical constant which depend on the liquid properties and channel dimensions). The flow dynamics of the liquids with low viscosity show a dependence on the channel width and the droplet volume, while the flow of liquids with high viscosity is mainly controlled by the viscous forces.

Surface engineering can be used to prevent ice accumulation and adhesion in environments that deal with icing problems. One recent engineering approach, slippery liquid infused porous surfaces (SLIPS), comprises a smooth and slippery lubricating surface, where lubricant is trapped within the pores of a solid material to repel various substances, such as water and ice. However, it remains unclear whether the slippery surfaces retain their icephobic characteristics under the impact of supercooled water droplets or repeated freezing and melting cycles. Here, the icephobic properties of SLIPS are evaluated under multiple droplet freeze–thaw and ice accretion–detachment cycles and compared to hydrophobic and superhydrophobic surfaces. The experiments are designed to mimic real environmental conditions, thus, the icephobicity is investigated in icing wind tunnel, where ice accretion occurs through the impact of supercooled water droplets. The adhesion of ice remained extremely low, <10 kPa, which is four times lower than ice adhesion onto smooth fluoropolymer surfaces, even after repeated ice accretion–detachment cycles. Moreover, cyclic droplet freeze–thaw experiments provide insight into the effects of temperature cycling on SLIPS wettability, showing stable wetting performance. The results suggest liquid infused porous surfaces as a potential solution to icephobicity under challenging and variating environmental conditions.

No abstract

Slippery, liquid-infused porous surfaces offer a promising route for producing omniphobic and anti-icing surfaces. Typically, these surfaces are made as a coating with expensive and time consuming assembly methods or with fluorinated films and oils. We report on a route for producing liquid-infused surfaces, which utilizes a liquid precursor fed oxygen-hydrogen flame to produce titania nanoparticles deposited directly on a low-density polyethylene film. This porous nanocoating, with thickness of several hundreds of nanometers, is then filled with silicone oil. The produced surfaces are shown to exhibit excellent anti-icing properties, with an ice adhesion strength of ∼12 kPa, which is an order of magnitude improvement when compared to the plain polyethylene film. The surface was also capable of maintaining this property even after cyclic icing testing.

No abstract

The chemical composition of a TiO2 nanoparticle coated paper surface was analyzed using time-of-flight secondary ion mass spectrometry (ToF-SIMS) to study the interconnection between wettability and surface chemistry on the nanoscale. In this work, a superhydrophobic TiO2 surface rich in carboxyl-terminated molecules was created by a liquid flame spray process. The TiO2 nanoparticle coated paper surface can be converted by photocatalytic oxidation into a highly hydrophilic one. Interestingly, the hydrophilic surface can be converted back into a superhydrophobic surface by heat treatment. The results showed that both ultraviolet A (UVA) and oven treatment induce changes in the surface chemistry within a few nanometers of the paper surface. These findings are consistent with those from our previously reported X-ray photoelectron spectroscopy (XPS) analysis, but the ToF-SIMS analysis yields more accurate insight into the surface chemistry.

No abstract