In this work, a new interface for continuous on-line MALDI-TOF MS is presented. The sample, mixed with a suitable matrix, was transported into the evacuated source chamber of the mass spectrometer at liquid flow rates of 100-400 nL/min. The liquid sample matrix was deposited on a rotating quartz wheel and transported to the repeller, where laser desorption took place. Rapid evaporation of the solvent (water or methanol) on the surface of the wheel resulted in formation of a thin, approximately 50-micron-wide, sample trace. Scanning electron microscopic photographs of the vacuum-dried trace revealed the deposited material to consist of an amorphous film. Furthermore, sample uniformity along the trace, in conjunction with its narrow width, resulted in excellent signal reproducibility, with detection limits in the attomole range. The interface permitted the on-line coupling of microcolumn separation techniques with MALDI MS, as demonstrated in the capillary electrophoresis MALDI-TOF MS analysis of a 12-peptide mixture. The approach offers the potential for rapid separation and trace analysis of complex mixtures.

We examined changes in a poly(ethylene oxide) (PEO) coating by continuously monitoring the electroosmotic flow (EOF) in a fused-silica capillary during electrophoresis. An imaging CCD camera was used to follow the motion of a fluorescent neutral marker zone along the length of the capillary. The PEO coating was shown to reduce the velocity of EOF by more than 1 order of magnitude compared to a bare capillary at pH 7.0. However, it did not reduce EOF efficiently at pH 8.2. The coating protocol was important, especially at an intermediate pH of 7.7. Capillary reconditioning with an acidified solution of PEO was necessary in order to create a stable and efficient coating. In all cases we observed a gradual increase of EOF during extended runs, suggesting that the coating is slowly being degraded. The increase of pH in the cathodic (detection-end) buffer reservoir beyond pH ∼8.0, e.g., as a result of electrolysis, had a large impact on the stability of the coating. This phenomenon may be used for the efficient and fast regeneration of the column surface and provides a simpler and more reliable alternative to pressure flushing of the capillary.

An improved vacuum deposition interface for coupling capillary electrophoresis with MALDI-TOF MS has been developed. Liquid samples consisting of analyte and matrix were deposited on a moving tape in the evacuated source chamber of a TOF mass spectrometer, enabling 24 h of uninterrupted analysis. The vacuum deposition procedure was compared with the dried-droplet method, and it was found that vacuum deposition generated significantly more reproducible signal intensity, eliminating the need for "sweet spot" searching. A concentration detection limit in the low-nanomolar range has been achieved with a low-attomole amount of sample consumed per spectrum. In addition, ion suppression caused by hydrophobicity differences in the analytes was reduced. To minimize ion suppression further, separation prior to MALDI MS analysis was employed. The performance of capillary electrophoresis (CE)-MALDI-TOF MS using the vacuum deposition interface was evaluated with a peptide mixture injected at low-femtomole levels. All peptides were baseline resolved with separation efficiencies in the range of 250000-400000 plates/m (2-3-s band half-width), demonstrating the high separation efficiency of the CE-MALDI MS coupling. A fast (approximately 40 s) CE separation of a mixture of angiotensins was found to reduce significantly ion suppression and enable trace level detection. It was also shown, for the analysis of an enolase digest, that sequence coverage of 65% was obtained using CE separation compared to 52% using step-elution solid-phase extraction and 44% in the control experiment using an unseparated mixture.

High-resolution capillary electrophoresis has been coupled to MALDI-TOF and TOF/TOF MS through off-line vacuum deposition onto standard stainless steel MALDI targets. This off-line approach allowed the decoupling of the separation from the MS analysis, thus allowing each to be independently optimized in terms of time. Using BSA tryptic digest as a model sample, the deposited streaks, roughly 100-microm wide, were first analyzed in the MS mode, consuming only a fraction of the sample. After data analysis, segments of the deposited trace, containing unidentified peptides, as well as several species chosen for sequence confirmation, were reanalyzed in the MS/MS mode using MALDI-TOF/TOF MS. Additionally, it is shown that the shot-to-shot reproducibility of the vacuum-deposited trace (5% RSD) is 1 order of magnitude lower than that found for the standard dried droplet method. Moreover, a linear dependence of signal intensities (relative to an internal standard) over 3 orders of magnitude was found for a peptide sample with concentrations ranging from 1 to 1000 nM. This paper demonstrates the potential of off-line coupling of high-resolution separations to MALDI-MS and MALDI-MS/MS using vacuum deposition for the analysis of complex peptide mixtures from protein digests.

We previously introduced a vacuum deposition interface for matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI/TOF MS) on a moving surface (e.g., quartz wheel, Mylar tape, metal target). In our present work, the approach has been extended to demonstrate parallel analysis for multiple on-line infusion MALDI MS and capillary array electrophoresis (CAE)-MALDI MS. In the infusion mode, individual peptide samples were simultaneously deposited on a Mylar tape cartridge using an array of eight capillaries, yielding eight parallel traces. For CAE-MALDI/TOF MS, the same number of separation capillaries were coupled with an array of eight infusion capillaries using a common liquid junction, containing matrix solution. A fast-scanning mirror was employed to traverse the beam of the desorption laser across the Mylar tape to probe one trace at a time. The positions of the eight sample traces formed on the tape were automatically determined, and all samples were analyzed in rapid sequence using a kilohertz repetition rate laser and a high-throughput data acquisition system. The instrumentation was operated with CAE MS for high-throughput analysis without compromising data quality. The principles of parallel separation-vacuum deposition should be generally applicable to MALDI/TOF MS analysis for proteomics and other areas where separation and high throughput are required.

Miniaturized, portable instrumentation has been gaining popularity in all areas of analytical chemistry. Capillary electrophoresis (CE), due to its main strengths of high separation efficiency, relatively short analysis time and low consumption of chemicals, is a particularly suitable technique for use in portable analytical instrumentation. In line with the general trend in miniaturization in chemistry utilizing microfluidic chips, the main thrust of portable CE (P-CE) systems development is towards chip-based miniaturized CE. Despite this, capillary-based (non-chip) P-CE systems have certain unmatched advantages, especially in the relative simplicity of the regular cylindrical geometry of the CE capillary, maximal volume-to-surface ratio, no need to design and to fabricate a chip, the low costs of capillary compared to chip, and better performance with some detection techniques. This review presents an overview of the state of the art of P-CE and literature relevant to future developments. We pay particular attention to the development and the potential of miniaturization of functional parts for P-CE. These include components related to sample introduction, separation and detection, which are the key elements in P-CE design. The future of P-CE may be in relatively simple, rugged designs (e.g., using a short piece of capillary fixed to a chip-sized platform on which injection and detection parts can be mounted). Electrochemical detection is well suited for miniaturization, so is probably the most suitable detection technique for P-CE, but optical detection is gaining interest, especially due to miniaturized light sources (e.g., light-emitting diodes).

Visualizing the differential distribution of carbon–carbon double bond (CC db) positional isomers of unsaturated phospholipids (PL) in tissue sections by use of refined matrix-assisted laser desorption ionization mass spectrometry imaging (MALDI MSI) technologies offers a high promise to deeper understand PL metabolism and isomer-specific functions in health and disease. Here we introduce an on-tissue ozonization protocol that enables a particular straightforward derivatization of unsaturated lipids in tissue sections. Collision-induced dissociation (CID) of MALDI-generated ozonide ions (with yields in the several ten percent range) produced the Criegee fragment ion pairs, which are indicative of CC db position(s). We used our technique for visualizing the differential distribution of Δ9 and Δ11 isomers of phosphatidylcholines in mouse brain and in human colon samples with the desorption laser spot size 15 μm, emphasizing the potential of the technique to expose local isomer-specific metabolism of PLs.

This work for the first time combines three on-capillary detection methods, namely, capacitively coupled contactless conductometric (C(4)D), photometric (PD), and fluorimetric (FD), in a single (identical) point of detection cell, allowing concurrent measurements at a single point of detection for use in capillary electrophoresis, capillary electrochromatography, and capillary/nanoliquid chromatography. The novel design is based on a standard 6.3 mm i.d. fiber-optic SMA adapter with a drilled opening for the separation capillary to go through, to which two concentrically positioned C(4)D detection electrodes with a detection gap of 7 mm were added on each side acting simultaneously as capillary guides. The optical fibers in the SMA adapter were used for the photometric signal (absorbance), and another optical fiber at a 45 degrees angle to the capillary was applied to collect the emitted light for FD. Light emitting diodes (255 and 470 nm) were used as light sources for the PD and FD detection modes. LOD values were determined under flow-injection conditions to exclude any stacking effects: For the 470 nm LED limits of detection (LODs) for FD and PD were for fluorescein (1 x 10(-8) mol/L) and tartrazine (6 x 10(-6) mol/L), respectively, and the LOD for the C(4)D was for magnesium chloride (5 x 10(-7) mol/L). The advantage of the three different detection signals in a single point is demonstrated in capillary electrophoresis using model mixtures and samples including a mixture of fluorescent and nonfluorescent dyes and common ions, underivatized amino acids, and a fluorescently labeled digest of bovine serum albumin.