A new measurement system, consisting of a mobile array of 50 microphones that form a spherical surface of radius 0.2 m, that images the acoustic intensity vector throughout a large volume is discussed. A simultaneous measurement of the pressure field across all the microphones provides time-domain holograms. Spherical harmonic expansions are used to convert the measured pressure into a volumetric vector intensity field on a grid of points ranging from the origin to a maximum radius of 0.4 m. Displays of the volumetric intensity image are used to locate noise sources outside the volume. There is no restriction on the type of noise source that can be studied. An experiment inside a Boeing 757 aircraft in flight successfully tested the ability of the array to locate flow-noise-excited sources on the fuselage. Reference transducers located on suspected noise source locations can also be used to increase the ability of this device to separate and identify multiple noise sources at a given frequency by using the theory of partial field decompositions. The frequency range of operation is 0 to 1400 Hz. This device is ideal for the diagnostic analysis of noise sources in commercial and military transportation vehicles in air, on land, and underwater.
A house on Edwards Air Force Base, CA, was exposed to low-intensity N-wave sonic booms during a 3-week test period in June 2006. The house was instrumented to measure the booms both inside and out. F-18 aircraft were flown to achieve a variety of boom overpressures from approximately 0.01 to 0.06 psf. During 4 test days, 77 test subjects heard the booms while seated inside and outside the house. Using the Magnitude Estimation methodology and artificial reference sounds, the subjects rated the annoyance of the booms. Since the same subjects heard similar booms both inside and outside the house, comparative ratings of indoor and outdoor annoyance were obtained. Preliminary results from this test will be presented.
A facility has been constructed at NASA Langley Research Center to simulate the soundscape inside residential houses that are exposed to environmental noise from aircraft. This controllable indoor listening environment, the Interior Effects Room, enables systematic study of parameters that affect psychoacoustic response. The single-room facility, built using typical residential construction methods and materials, is surrounded on adjacent sides by two arrays of loudspeakers in close proximity to the exterior walls. The arrays, containing 52 subwoofers and 52 mid-range speakers, have a usable bandwidth of 3 Hz to 5 kHz and sufficient output to allow study of sonic boom noise. In addition to these exterior arrays, satellite speakers placed inside the room are used to augment the transmitted sound with rattle and other audible contact-induced noise that can result from low frequency excitation of a residential house. The layout of the facility, operational characteristics, acoustic characteristics and equalization approaches are summarized.
Composite structures are often used in aircraft because of the advantages offered by a high strength to weight ratio. However, the acoustical properties of these light and stiff structures can often be less than desirable resulting in high aircraft interior noise levels. In this paper, measurements and predictions of the transmission loss of a curved honeycomb composite panel are presented. The transmission loss predictions are validated by comparisons to measurements. An assessment of the behavior of the panel is made from the dispersion characteristics of transverse waves propagating in the panel. The speed of transverse waves propagating in the panel is found to be sonic or supersonic over the frequency range from 100 to 5000 Hz. The acoustical benefit of reducing the wave speed for transverse vibration is demonstrated. IntroductionPanels constructed from face sheets laminated to a honeycomb core are being incorporated into the design of modern aircraft fuselage and trim treatments. The mechanical properties of these panels offer a distinct advantage in weight over other commonly used construction materials.* The strength to weight ratio of honeycomb composite panels is high in comparison to rib stiffened aluminum panels used in previous generations of aircraft. However, the high stiffness and low weight can result in supersonic wave propagation at relatively low frequencies, which adversely affects the acoustical performance at these frequencies. †Poor acoustical performance of these types of structures can increase the cabin noise levels to which the passengers and crew are exposed.
Most general aviation aircraft utilize single layer plexiglas material for the windshield and side windows. Adding noise control treatments to transparent panels is a challenging problem. In this paper, damped plexiglas windows are evaluated for replacement of conventional windows in general aviation aircraft to reduce the structure-borne and airborne noise transmitted into the interior. In contrast to conventional solid windows, the damped plexiglas window panels are fabricated using two or three layers of plexiglas with transparent viscoelastic damping material sandwiched between the layers. Results from acoustic tests conducted in the NASA Langley Structural Acoustic Loads and Transmission (SALT) facility are used to compare different designs of the damped plexiglas panels with solid windows of the same nominal thickness. Comparisons of the solid and damped plexiglas panels show reductions in the radiated sound power of up to 8 dB at low frequency resonances and as large as 4.5 dB over a 4000 Hz bandwidth. The weight of the viscoelastic treatment was approximately 1 % of the panel mass. Preliminary FEM/BEM modeling shows good agreement with experimental results for radiated sound power.
The validation of finite element and boundary element model for the vibro-acoustic response of a curved honeycomb core composite aircraft panel is completed. The finite element and boundary element models were previously validated separately. This validation process was hampered significantly by the method in which the panel was installed in the test facility. The fixture used was made primarily of fiberboard and the panel was held in a groove in the fiberboard by a compression fitting made of plastic tubing. The validated model is intended to be used to evaluate noise reduction concepts from both an experimental and analytic basis simultaneously. An initial parametric study of the influence of core thickness on the radiated sound power from this panel, using this numerical model was subsequently conducted. This study was significantly influenced by the presence of strong boundary condition effects but indicated that the radiated sound power from this panel was insensitive to core thickness primarily due to the offsetting effects of added mass and added stiffness in the frequency range investigated.
The Exterior Effects Room (EER), located at the NASA Langley Research Center, is a facility built for psychoacoustic studies of aircraft community noise. Recently, the EER was significantly upgraded to allow for simulation of aircraft flyovers in a 3-D audio and visual environment. The upgrade included installation of 27 satellite and 4 subwoofer loudspeakers that are driven by a real-time audio server. The audio server employs an implementation of the vector base amplitude panning method to position virtual sources at arbitrary azimuth and elevation angles in the EER. Real-time application of filters, time delays, and gains are required to compensate for installation effects, including those associated with the irregular room geometry, colorization due to varying loudspeaker installations, and crossover filtering. The authors previously showed [J. Acoust. Soc. Am., 127, 1969 (2010)] that color compensation and crossover filtering could be achieved for satellite and subwoofer loudspeakers. However, the resulting FIR filters were too long (32 768 taps) to implement in real-time. The focus of this work is on the development of reduced-length surrogate IIR filters and on the measurement of the acoustic performance of the installed real-time system.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.