Recent experiments on the Type I ELMy H-mode regime performed at JET with improved diagnostics have expanded the range of parameters for the study of Type I ELM energy and particle losses. Deviations from the standard behaviour of such losses in some areas of the Type I ELMy H-mode operating space have revealed that the ELM losses are correlated with the parameters (density and temperature) of the pedestal plasma before the ELM crash, while other global ELM characteristics (such as ELM frequency) are a consequence of the ELMdriven energy and particle flux and of the in-between ELM energy and particle confinement. The relative Type I ELM plasma energy loss (to the pedestal energy) is found to correlate well with the collisionality of the pedestal plasma, showing a weak dependence on the method used to achieve those pedestal plasma parameters: plasma shaping, heating, pellet injection and impurity seeding. Effects of edge plasma collisionality and transport along the magnetic field on the Type I ELM particle and energy fluxes onto the divertor target have also been observed. Two possible physical mechanisms that may give rise to the observed collisionality dependence of ELM energy losses are proposed and their consistency with the experimental measurements investigated: collisionality dependence of the edge bootstrap current with its associated influence on the ELM MHD origin and the limitation of the ELM energy loss by the impedance of the divertor target sheath to energy flow during the ELM event.

Demonstrating improved confinement of energetic ions is one of the key goals of the Wendelstein 7-X (W7-X) stellarator. In the past campaigns, measuring confined fast ions has proven to be challenging. Future deuterium campaigns would open up the option of using fusion-produced neutrons to indirectly observe confined fast ions. There are two neutron populations: 2.45 MeV neutrons from thermonuclear and beam-target fusion, and 14.1 MeV neutrons from DT reactions between tritium fusion products and bulk deuterium. The 14.1 MeV neutron signal can be measured using a scintillating fiber neutron detector, whereas the overall neutron rate is monitored by common radiation safety detectors, for instance fission chambers. The fusion rates are dependent on the slowing-down distribution of the deuterium and tritium ions, which in turn depend on the magnetic configuration via fast ion orbits. In this work, we investigate the effect of magnetic configuration on neutron production rates in W7-X. The neutral beam injection, beam and triton slowing-down distributions, and the fusion reactivity are simulated with the ASCOT suite of codes. The results indicate that the magnetic configuration has only a small effect on the production of 2.45 MeV neutrons from DD fusion and, particularly, on the 14.1 MeV neutron production rates. Despite triton losses of up to 50 %, the amount of 14.1 MeV neutrons produced might be sufficient for a time-resolved detection using a scintillating fiber detector, although only in high-performance discharges.

Observations of bulk plasma rotation in radio frequency (RF) heated JET discharges are reported. This study is concentrated on RF heated L-mode plasmas. In particular, the toroidal rotation profiles in plasmas heated by ion cyclotron resonance frequency (ICRF) waves and lower hybrid (LH) waves have been analysed. It is the first time that rotation profiles in JET plasmas with LH waves have been measured in dedicated discharges. It is found that the toroidal plasma rotation in the outer region of the plasmas is in the co-current direction irrespective of the heating scenario. An interesting feature is that the toroidal rotation profile appears to be hollow in many discharges at low plasma current, but a low current in itself does not seem to be a sufficient condition for finding such profiles. Fast ion transport and finite orbit width effects are mechanisms that could explain hollow rotation profiles. This possibility has been investigated by numerical simulations of the torque on the bulk plasma due to fast ICRF accelerated ions. The obtained torque is used in a transport equation for the toroidal momentum density to estimate the effect on the thermal bulk plasma rotation profile.

After completing the main construction phase of Wendelstein 7-X (W7-X) and successfully commissioning the device, first plasma operation started at the end of 2015. Integral commissioning of plasma start-up and operation using electron cyclotron resonance heating (ECRH) and an extensive set of plasma diagnostics have been completed, allowing initial physics studies during the first operational campaign. Both in helium and hydrogen, plasma breakdown was easily achieved. Gaining experience with plasma vessel conditioning, discharge lengths could be extended gradually. Eventually, discharges lasted up to 6 s, reaching an injected energy of 4 MJ, which is twice the limit originally agreed for the limiter configuration employed during the first operational campaign. At power levels of 4 MW central electron densities reached 3  ×  1019 m−3, central electron temperatures reached values of 7 keV and ion temperatures reached just above 2 keV. Important physics studies during this first operational phase include a first assessment of power balance and energy confinement, ECRH power deposition experiments, 2nd harmonic O-mode ECRH using multi-pass absorption, and current drive experiments using electron cyclotron current drive. As in many plasma discharges the electron temperature exceeds the ion temperature significantly, these plasmas are governed by core electron root confinement showing a strong positive electric field in the plasma centre.

After many years of fusion research, the conditions needed for a D–T fusion reactor have been approached on the Tokamak Fusion Test Reactor (TFTR) [Fusion Technol. 21, 1324 (1992)]. For the first time the unique phenomena present in a D–T plasma are now being studied in a laboratory plasma. The first magnetic fusion experiments to study plasmas using nearly equal concentrations of deuterium and tritium have been carried out on TFTR. At present the maximum fusion power of 10.7 MW, using 39.5 MW of neutral-beam heating, in a supershot discharge and 6.7 MW in a high-βp discharge following a current rampdown. The fusion power density in a core of the plasma is ≊2.8 MW m−3, exceeding that expected in the International Thermonuclear Experimental Reactor (ITER) [Plasma Physics and Controlled Nuclear Fusion Research (International Atomic Energy Agency, Vienna, 1991), Vol. 3, p. 239] at 1500 MW total fusion power. The energy confinement time, τE, is observed to increase in D–T, relative to D plasmas, by 20% and the ni(0) Ti(0) τE product by 55%. The improvement in thermal confinement is caused primarily by a decrease in ion heat conductivity in both supershot and limiter-H-mode discharges. Extensive lithium pellet injection increased the confinement time to 0.27 s and enabled higher current operation in both supershot and high-βp discharges. Ion cyclotron range of frequencies (ICRF) heating of a D–T plasma, using the second harmonic of tritium, has been demonstrated. First measurements of the confined alpha particles have been performed and found to be in good agreement with TRANSP [Nucl. Fusion 34, 1247 (1994)] simulations. Initial measurements of the alpha ash profile have been compared with simulations using particle transport coefficients from He gas puffing experiments. The loss of alpha particles to a detector at the bottom of the vessel is well described by the first-orbit loss mechanism. No loss due to alpha-particle-driven instabilities has yet been observed. D–T experiments on TFTR will continue to explore the assumptions of the ITER design and to examine some of the physics issues associated with an advanced tokamak reactor.

A model for the transition to the radiatively improved (RI) mode triggered in tokamaks by seeding of impurities is proposed. This model takes into account that with increasing plasma effective charge the growth rate of the toroidal ion temperature gradient (ITG) instability, considered nowadays as the dominant source of anomalous energy losses in low-confinement (L) mode, decreases. As a result the plasma density profile peaks due to an inward convection generated by trapped electron turbulence. This completely quenches ITG induced transport and a bifurcation to the RI mode occurs. Conditions necessary for the L-RI transition are investigated.

Results from the first measurements of a core plasma poloidal rotation velocity (upsilontheta) across internal transport barriers (ITB) on JET are presented. The spatial and temporal evolution of the ITB can be followed along with the upsilontheta radial profiles, providing a very clear link between the location of the steepest region of the ion temperature gradient and localized spin-up of upsilontheta. The upsilontheta measurements are an order of magnitude higher than the neoclassical predictions for thermal particles in the ITB region, contrary to the close agreement found between the determined and predicted particle and heat transport coefficients [K.-D. Zastrow, Plasma Phys. Controlled Fusion 46, B255 (2004)]. These results have significant implications for the understanding of transport barrier dynamics due to their large impact on the measured radial electric field profile.

This paper describes the content of an L-mode database that has been compiled with data from Alcator C-Mod, ASDEX, DIII, DIII-D, FTU, JET, JFT-2M, JT-60, PBX-M, PDX, T-10, TEXTOR, TFTR, and Tore-Supra. The database consists of a total of 2938 entries, 1881 of which are in the L-phase while 922 are ohmically heated only (OH). Each entry contains up to 95 descriptive parameters, including global and kinetic information, machine conditioning, and configuration. The paper presents a description of the database and the variables contained therein, and it also presents global and thermal scalings along with predictions for ITER. The L-mode thermal confinement time scaling, determined from a subset of 1312 entries for which the T E ,~F , are provided, is