Large Type-I Edge Localized Modes (ELMs) are completely eliminated with small n = 3 resonant magnetic perturbations (RMP) in low average triangularity, " = 0.26, plasmas and in ITER Similar Shaped (ISS) plasmas, " = 0.53, with ITER relevant collisionalities v e " # 0.2. Significant differences in the RMP requirements and in the properties of the ELM suppressed plasmas are found when comparing the two triangularities. In ISS plasmas, the current required to suppress ELMs is approximately 25% higher than in low average triangularity plasmas. It is also found that the width of the resonant q 95 window required for ELM suppression is smaller in ISS plasmas than in low average triangularity plasmas. An analysis of the positions and widths of resonant magnetic islands across the pedestal region, in the absence of resonant field screening or a self-consistent plasma response, indicates that differences in the shape of the q profile may explain the need for higher RMP coil currents during ELM suppression in ISS plasmas. Changes in the pedestal profiles are compared for each plasma shape as well as with changes in the injected neutral beam power and the RMP amplitude. Implications of these results are discussed in terms of requirements for optimal ELM control coil designs and for establishing the physics basis needed in order to scale this approach to future burning plasma devices such as ITER.

The pressure at the top of the edge transport barrier (or "pedestal height") strongly impacts fusion performance, while large Edge Localized Modes (ELMs), driven by the free energy in the pedestal region, can constrain material lifetimes. Accurately predicting the pedestal height and ELM behavior in ITER is an essential element of prediction and optimization of fusion performance. Investigation of intermediate wavelength MHD modes (or "peeling-ballooning" modes) has led to improved understanding of important constraints on the pedestal height and the mechanism for ELMs. The combination of high resolution pedestal diagnostics, including substantial recent improvements, and a suite of highly efficient stability codes, has made edge stability analysis routine on several major tokamaks, contributing both to understanding, and to experimental planning and performance optimization. Here we present extensive comparisons of observations to predicted edge stability boundaries on several tokamaks, both for the standard (Type I) ELM regime, and for small ELM and ELM-free regimes. We further use the stability constraint on pedestal height to test models of the pedestal width, and self-consistently combine a simple width model with peeling-ballooning stability calculations to develop a new predictive model (EPED1) for the pedestal height and width. This model is tested against experimental measurements, and used in initial predictions of the pedestal height for ITER.

This paper presents the experimental characterization of pedestal parameters, edge localized mode (ELM) energy, and particle losses from the main plasma and the corresponding ELM energy fluxes on plasma facing components for a series of dedicated experiments in the Joint European Torus (JET). From these experiments, it is demonstrated that the simple hypothesis relating the peeling-ballooning linear instability to ELM energy losses is not valid. Contrary to previous observations at lower triangularities, small energy losses at low collisionality have been obtained in regimes at high plasma triangularity and q95∼4.5, indicating that the edge plasma magnetohydrodynamic stability is linked with the transport mechanisms that lead to the loss of energy by conduction during type I ELMs. Measurements of the ELM energy fluxes on the divertor target show that their time scale is linked to the ion transport along the field and the formation of a high energy sheath, in agreement with kinetic modeling of ELMs. Higher density ELMs, of a convective nature, lead to overall much longer time scales for the ELM energy flux, with more than 80% of the ELM energy flux arriving after the surface divertor temperature has reached its maximum value. On the contrary, for low density ELMs, of a conductive nature, up to 40% of the energy flux arrives at the divertor target before the surface divertor temperature has reached its maximum value. These large and more conductive ELMs may lead to up to ∼50% of the ELM energy reaching the main wall plasma facing components instead of the divertor target. The extrapolation to the International Thermonuclear Experimental Reactor of the obtained results is described and the main uncertainties discussed.

This paper describes experiments with highly shaped JET H-mode plasmas, which were directed to developing regimes where Type I ELMs are replaced by other edge relaxations, while maintaining the pedestal pressure of Type I ELMy H-modes. It was found that Type II ELMs coexisted with Type I, up to densities of the order of the Greenwald limit, where Type III ELMs appear, and the good confinement was lost. Only at the highest edge collisionality was it observed that Type II ELMs completely replace Type I. At high β p and q 95 , 'grassy' ELMs replace Type I completely. The MHD spectra characteristics for grassy ELMs are significantly different from those of Type II ELMs. This paper details the experiments, briefly compares the results to those obtained elsewhere and suggests open lines of investigations for the assessment of the potential of grassy ELM regimes as an ELM mitigation technique.