As a unique two-dimensional nanomaterial, layered black phosphorus (BP) nanosheets have shown promising applications in electronics. Although mechanical exfoliation was successfully used to prepare BP nanosheets, it is still a challenge to produce novel BP nanostructures in high yield. A facile top-down approach for preparation of black phosphorus quantum dots (BPQDs) in solution is presented. The obtained BPQDs have a lateral size of 4.9±1.6 nm and thickness of 1.9±0.9 nm (ca. 4±2 layers). As a proof-of-concept application, by using BPQDs mixed with polyvinylpyrrolidone as the active layer, a flexible memory device was successfully fabricated that exhibits a nonvolatile rewritable memory effect with a high ON/OFF current ratio and good stability.

Black phosphorus, a fast emerging two-dimensional material, has been configured as field effect transistors, showing a hole-transport-dominated ambipolar characteristic. Here we report an effective modulation on ambipolar characteristics of few-layer black phosphorus transistors through in situ surface functionalization with caesium carbonate (Cs 2 CO 3 ) and molybdenum trioxide (MoO 3 ), respectively. Cs 2 CO 3 is found to strongly electron dope black phosphorus. The electron mobility of black phosphorus is significantly enhanced to B27 cm 2 V À 1 s À 1 after 10 nm Cs 2 CO 3 modification, indicating a greatly improved electrontransport behaviour. In contrast, MoO 3 decoration demonstrates a giant hole-doping effect. In situ photoelectron spectroscopy characterization reveals significant surface charge transfer occurring at the dopants/black phosphorus interfaces. Moreover, the surface-doped black phosphorus devices exhibit a largely enhanced photodetection behaviour. Our findings coupled with the tunable nature of the surface transfer doping scheme ensure black phosphorus as a promising candidate for further complementary logic electronics.

The concept of using single molecules as key building blocks for logic gates, diodes and transistors to perform basic functions of digital electronic devices at the molecular scale has been explored over the past decades. However, in addition to mimicking the basic functions of current silicon devices, molecules often possess unique properties that have no parallel in conventional materials and promise new hybrid devices with novel functions that cannot be achieved with equivalent solid-state devices. The most appealing example is the molecular switch. Over the past decade, molecular switches on surfaces have been intensely investigated. A variety of external stimuli such as light, electric field, temperature, tunneling electrons and even chemical stimulus have been used to activate these molecular switches between bistable or even multiple states by manipulating molecular conformations, dipole orientations, spin states, charge states and even chemical bond formation. The switching event can occur either on surfaces or in break junctions. The aim of this review is to highlight recent advances in molecular switches triggered by various external stimuli, as investigated by low-temperature scanning tunneling microscopy (LT-STM) and the break junction technique. We begin by presenting the molecular switches triggered by various external stimuli that do not provide single molecule selectivity, referred to as non-selective switching. Special focus is then given to selective single molecule switching realized using the LT-STM tip on surfaces. Single molecule switches operated by different mechanisms are reviewed and discussed. Finally, molecular switches embedded in self-assembled monolayers (SAMs) and single molecule junctions are addressed.

We report effective and stable electron doping of monolayer molybdenum disulfide (MoS2) by cesium carbonate (Cs2CO3) surface functionalization. The electron charge carrier concentration in exfoliated monolayer MoS2 can be increased by about 9 times after Cs2CO3 functionalization. The n-type doping effect was evaluated by in situ transport measurements of MoS2 field-effect transistors (FETs) and further corroborated by in situ ultraviolet photoelectron spectroscopy, X-ray photoelectron spectroscopy, and Raman scattering measurements. The electron doping enhances the formation of negative trions (i.e., a quasiparticle comprising two electrons and one hole) in monolayer MoS2 under light irradiation and significantly reduces the charge recombination of photoexcited electron-hole pairs. This results in large photoluminescence suppression and an obvious photocurrent enhancement in monolayer MoS2 FETs.

The two-dimensional material, molybdenum disulfide (MoS2), has attracted considerable attention for numerous applications in optoelectronics. Here, we demonstrate a plasmonic enhancement of photocurrent in MoS2 field-effect-transistor decorated with gold nanoparticles, with significantly enhanced photocurrent peaked at the plasmon resonant wavelength around 540 nm. Our findings offer a possibility to realize wavelength selectable photodetection in MoS2 based phototransistors.

Direct patterning of ultrathin MoS2 films with well-defined structures and controllable thickness is appealing since the properties of MoS2 sheets are sensitive to the number of layer and surface properties. In this work, we employed a facile, effective, and well-controlled technique to achieve micropatterning of MoS2 films with a focused laser beam. We demonstrated that a direct focused laser beam irradiation was able to achieve localized modification and thinning of as-synthesized MoS2 films. With a scanning laser beam, microdomains with well-defined structures and controllable thickness were created on the same film. We found that laser modification altered the photoelectrical property of the MoS2 films, and subsequently, photodetectors with improved performance have been fabricated and demonstrated using laser modified films.

In situ bottom-gated molybdenum disulfide (MoS2) field effect transistors (FETs) device characterization and in situ ultraviolet photoelectron spectroscopy and x-ray photoelectron spectroscopy measurements were combined to investigate the effect of surface modification layers of C60 and molybdenum trioxide (MoO3) on the electronic properties of single layer MoS2. It is found that C60 decoration keeps MoS2 FET performance intact due to the very weak interfacial interactions, making C60 as an ideal capping layer for MoS2 devices. In contrast, decorating MoO3 on MoS2 induces significant charge transfer at the MoS2/MoO3 interface and largely depletes the electron charge carriers in MoS2 FET devices.

No abstract