This paper concerns the analysis of five-layer corrugated paperboard subjected to a four-point bending test. The segment of paperboard was tested to determine the bending stiffness. The investigations were conducted experimentally and numerically. The non-damaging tests of bending were carried out in an elastic range of samples. The detailed layers of paperboard were modelled as an orthotropic material. The simulation of flexure was based on a finite element method using Ansys® software. Several material properties and thicknesses of papers in the samples were taken into account to analyse the influence on general stiffness. Two different discrete models based on two geometries of paperboard were considered in this study to validate the experimental stiffness. The present analysis shows the possibility of numerical modelling to achieve a good correlation with experimental results. Moreover, the results of numerical estimations indicate that modelling of the perfect structure gives a lower bending stiffness and some corrections of geometry should be implemented. The discrepancy in stiffness between both methods ranged from 3.04 to 32.88% depending on the analysed variant.
The present paper analyses the properties of printed polylactic acid (PLA) samples with admixtures of graphene nanopowder (GNP) at wt. 1%, 2% and 4%. The pure polylactide and admixed polylactide printed samples were examined to determine their chemical-physical properties, stiffness, and strength parameters. The tests of tensile, dynamic mechanical analysis (DMA), difference thermogravimetric (TG), and differential scanning calorimetry (DSC) were executed before and after UV (ultraviolet) treatment. The first part of the paper shows the process of manufacturing granulates and filaments mixed with graphene. The second part of the paper concerns the results of the tests made on printed samples. The analysed samples were printed using a Prusa i3 MK3 printer. It transpired that the content of graphene at 1% improved the mechanical parameters of the printed composite by organising its structure. Increasing the amount of graphene caused the values of the measured parameters to drop. This research indicates how important it is to determine the optimal values of nanoadditives in biopolymers.
The aim of this work was to verify the material properties of polylactic acid (PLA) with an addition of carbon nanotubes (CNTs) or graphene nanopowder (GNP). The pure polylactide and admixed polylactide samples were subjected to chemical–physical tests to determine their stiffness and strength parameters. The tensile and impact tests were performed on samples without UV (ultraviolet) treatment and after UV treatment, in a physiological saline solution. The investigations were composed of two stages. The first one was related to the examination of the properties of pure polylactide, denoted as the following: 3001D, 4032D, and 4043D. The second stage was based on an analysis of the properties of PLA 4032D with an admixture of GNP or CNTs, at 0.1 wt.% and 0.5 wt.%. By comparing the strength and the stiffness of pure samples with samples with the considered admixtures, an essential increase was not observed. However, it is stated that the presence of GNP and CNTs in the samples positively influenced the resistance of the materials to the ageing process.
The literature review concerning various materials for production of sheet piles used in wet ground, waterfront and marine conditions has been presented. Polyvinyl chloride has been identified as a promising steel alternative. Despite unambiguous findings suggesting a higher environmental impact of steel sheet piles compared to polymer products, the necessity of further detailed surveys, confirming the preliminary conclusion, has been perceived. The main objective of this study has been to compare the environmental impact of steel and vinyl sheet piles taking into consideration various corrosion rate depending on the local conditions. The comparative life cycle assessment analyses have been carried out according to a cradle-to-site approach. The comparison of indicators has shown that the environmental impact of polymer products had been significantly lower than that of steel products. In case of the most aggressive environment, the differences of results have reached an order of magnitude. The dominant environmental impact has resulted from the production process of sheet piles. An uncertainty analysis has been carried out by means of Monte Carlo simulations. The study has also provided sensitivity analysis to the assumptions of the model applied. The minimum thickness of steel sheet piles after 50 years of use, including loss allowances and protective coatings, as well as different parameters of transport has been analyzed. Irrespective of the assumed conditions, the general conclusion has remained the same: steel sheet piles indicated significantly higher environmental impact than vinyl sheet piles.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.