For some time we have experimented at the Eindhoven University of Technology with a system which provides students with an electronic feedback path to the lecturer, audience paced feedback (APF). In this paper we describe this APF system, and give indications of its effectiveness.

No abstract

The production of compound adhesives using disparate ingredients is seen as some of the best evidence of advanced cognition outside of the use of symbolism. Previous field and laboratory testing of adhesives has shown the complexities involved in creating an effective Middle Stone Age glue using Acacia gum. However, it is currently unclear how efficient different adhesive recipes are, how much specific ingredients influence their performance, and how difficult it may have been for those ingredients to be combined to maximum effect. We conducted a series of laboratory-based lap shear and impact tests, following modern adhesion testing standards, to determine the efficacy of compound adhesives, with particular regard to the ingredient ratios. We tested rosin (colophony) and gum adhesives, containing additives of beeswax and ochre in varying ratios. During both lap shear and impact tests compound rosin adhesives performed better than single component rosin adhesives, and pure acacia gum was the strongest. The large difference in performance between each base adhesive and the significant changes in performance that occur due to relatively small changes in ingredient ratios lend further support to the notion that high levels of skill and knowledge were required to consistently produce the most effective adhesives.

No abstract

The current study focuses on the development of silanized graphene oxide reinforced basalt fiber/epoxy composites for enhanced tribological and viscoelastic properties. The modified-graphene oxide nanoplatelets were characterized using energy-dispersive X-ray spectroscopy, and Raman analyses. Pin-on-disk wear test and dynamic mechanical thermal analysis were conducted to determine the tribological and viscoelastic properties of the fabricated specimens with different silanized-graphene oxide loadings in the matrix (0–0.5 wt.% at a step of 0.1). The multiscale specimens were fabricated using the hand lay-up technique. The best silanized-graphene oxide loading for effectively enhancing the tribological properties was found to be 0.4 wt.%, whose wear rate and friction coefficient were 62% and 44%, respectively lower than those of the neat basalt/epoxy composite. The examination of the worn surfaces showed the enhanced basalt fiber/epoxy bonding in graphene oxide-reinforced specimen. From the results of dynamic mechanical thermal analysis, the specimen filled with 0.4 wt.% silanized-graphene oxide demonstrated the highest increase of 130% and 13.6℃ in the storage modulus and glass transition temperature as compared to the neat composite. This study indicated that the addition of silanized-graphene oxide considerably enhanced the tribological and viscoelastic properties of the fibrous composites.

SynopsisAn expression is derived for the Van der Waals force between two semi-infinite bodies with small surface irregularities. Calculations are given both for the plane-plane and the plane-sphere configuration. The value of the correction from the surface irregularities upon the Van der Waals force is shown to amount easily to lo-50%.

No abstract

Adhesives are an important yet often overlooked aspect of human tool use. Previous experiments have shown that compound resin/gum adhesive production by anatomically modern humans was a cognitively demanding task that required advanced use of fire, forward planning, and abstraction among other traits. Yet the oldest known adhesives were produced by Neandertals, not anatomically modern humans. These tar or pitch adhesives are an entirely different material, produced from a distinct, albeit similarly complex process. However, the material properties of these adhesives and the influence of the production process on performance is still unclear. To this end we conducted a series of laboratory based lap shear and impact tests following modern adhesive testing standards and at three different temperatures to measure the strength of pine and birch pitch adhesives. We tested eight different recipes that contain charcoal as an additive (mimicking contamination) or were reduced by boiling for different lengths of time. Lap shear tests were conducted on wood and flint adherends to determine shear strength on different materials, and we conducted high load-rate tests to understand how the same material behaves under impact forces. Our results indicate that both pine and birch pitch adhesives behave similarly at room temperature. Pine pitch is highly sensitive to the addition of charcoal and further heating. Up to a certain extent charcoal additives increases performance, as does extra seething. However, too much charcoal and seething will reduce performance. Similarly, pine pitch is sensitive to ambient temperature changes and it is strongest at 0°C and weakest at 38°C. Adhesive failures occur in a similar manner on flint and wood suggesting the weakest part of a flint-adhesive-wood composite tool may have been the cohesive strength of the adhesive. Finally, pine pitch adhesives may be better suited to resisting high-load rate impacts than shear forces. Our experiments show that pitch production and post-production manipulation are sensitive processes, and to obtain a workable and strong adhesive one requires a deep understanding of the material properties. Our results validate previous archaeological adhesive studies that suggest that the manufacture and use of adhesives was an advanced technological process.