Based on the results of a numerical-field analysis of the distribution of the magnetic force field in the working area of the disk magnetic separator, designed to clean bulk substances from ferromagnetic inclusions, the influence of the magnetic material of the poles of the magnetic system on the field distribution is determined. A consistent study of two magnetic systems assembled on the basis of magnetic materials of different classes is carried out. The finite element method implemented in the COMSOL Multiphysics software environment is used to calculate the distribution of magnetic induction in a disk magnetic separator with rare-earth and ferrite magnets. Due to the complexity of the spatial geometry of the force field in the working area of the disk magnetic separator, a three-dimensional model of the magnetic system is developed. A comparative analysis of the distribution of the magnetic force field in the working area of the disk separator with a highly coercive magnetic system and with a magnetic system based on ferrite blocks is carried out. As a result of the analysis, it is found that the indicators of the intensity and heterogeneity of the magnetic field for a highly coercive magnetic system significantly exceed the corresponding parameters of a ferrite magnetic system. It is proved that when choosing magnets for the magnetic system of a disk separator, preference should be given to highly coercive alloys, the magnetic properties of which significantly exceed the magnetic properties of ferrite magnets. To reduce the cost of the magnetic system of the disk separator, the use of a combined magnetic system assembled from magnetic materials of different classes is proposed. Studies of combined magnetic systems with various mass fractions of magnetic materials are done. The ratio of the mass fractions of magnets of various properties in the poles of the magnetic system is determined, at which sufficiently high magnetic characteristics are provided in the working area. It is shown that the presence of a ferrite fraction in the magnetic poles not only reduces the cost of the magnetic system of the separator, but also reduces the mass of the system. The tasks of further research are justified.
Currently, in transport systems, as part of the main and auxiliary equipment, a large number of induction motors with a squirrel-cage rotor of different capacities are used. Their wide application in the transport industry is associated with the main advantages over other types of machinesa fairly high reliability, low cost and ease of maintenance. However, during the operation of these motors, a number of malfunctions can occur that affect the deterioration of the performance of the entire drive, the accuracy of its functions, or accelerate an emergency stop. To ensure proper control of the technical condition of electric motors, modern diagnostic systems are required that operate in real-time and operational loading mode with the transmission of data on the instantaneous state of the main control elements. The paper proposes a block diagram of the diagnostic built-in system and developed a modular unit for it to set the type and degree of the most complex damageinter-turn short circuit in the stator winding.
У статті розглянуті дослідження розподілу магнітного поляв міжполюсному проміжку відкритих вісесиметричних магнітних систем. Отримано рівняння з граничними умовами, рішення якого дозволяє скоротити обсяг подальших чисельних методів розрахунків.Для ряду нестійких завдань математичної фізики Р.Латтесом і Ж.Лионсом розроблений метод квазізвернення, який може бути застосований як для еволюційних завдань, так і стаціонарних. Основна ідея методу квазізвернення полягає в належній зміні диференціальних операторів, що входять в завдання. Ця зміна робиться введенням додаткових диференціальних членів. Застосування цього методу дозволяє ефективно використати чисельні методи розрахунку крайового завдання для відкритих осесиметричних систем.
У статті наводиться огляд проблем, що зустрічаються при моделюванні механічних процесів. Так само проведено аналіз застосування модуля «Механіка конструкцій» в програмному середовищі COMSOL Multiphysics для вирішення механічних завдань на прикладі моделі яка представляє собою тонкий металевий лист, який вдавлюється в штамп за допомогою пуансона. При прокаті листового металу явище деформації – є важливим етапом в технологічному процесі. Тому в роботі показана можливість застосування моделювання механічних процесів, як можливість проводити експериментальні дослідження за допомогою COMSOL Multiphysics. Також в роботі поведено аналіз літературних джерел, в яких розглядається питання моделювання механічних і фізичних процесів не тільки в програмному середовищі COMSOL Multiphysics., але і в інших програмних продуктах.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.