No abstract

The produced water, which could be a complex mixture of different organic and inorganic compounds (mostly salts, minerals and oils) is a major wastewater stream generated during oil and gas production processes. Due to increase oil and gas exploration and production, especially from unconventional resources like shale oil and gas reservoirs, the volume of this effluent production is increasing around the world and its discarding to the environment is one of the global concerns.

No abstract

No abstract

Counter-current spontaneous imbibition (SI), in which water and oil flow through the same face in opposite directions, is known as one of the most significant oil recovery mechanisms in naturally fractured reservoirs; however, this mechanism has not received much attention. Understanding the dynamic of water-oil displacement during counter-current SI is very challenging because of simultaneous impacts of multiple factors including geometry complexity and heterogeneity of naturally fractured reservoir materials, e.g., high permeability contrast between the rock matrix and fracture, wettability, and porosity. This study investigates the effects of water injection velocity, fracture aperture, and grain shape during counter-current SI at pore-scale. A robust finite element solver is used to solve the governing equations of multiphase flow, which are the coupled Navier–Stokes and Cahn–Hilliard phase-field equations. The results showed that the case with the highest injection velocity (uinj = 5 mm/s) recovered more than 15% of the matrix oil at the early times and then reached its ultimate recovery factor. However, in the case of the lowest injection velocity, i.e., uinj = 0.05 mm/s, the lowest imbibition rate was observed at the early times, but ultimately 23% of the matrix oil was recovered. The model with uinj = 5 mm/s was able to capture some pore-level mechanisms such as snap-off, oil film thinning, interface coalescence, and water film bridging. The obtained results revealed that changing the fracture aperture has a slight effect on the imbibition rate at the earlier times and ultimate recoveries would be almost equal. To assess the influences of grain shape on the imbibition process, the simulated domain was reconstructed with cubic grains. It was noticed that because of higher permeability and porosity, relatively larger oil drops were formed and resulted in higher oil recovery compared with the model with spherical grains. The developed model can be used as a basis for phase-field counter-current simulations and would be useful to study the qualitative and quantitative nature of this phenomenon.

: Wound healing is a varied and complex process designed to promptly restore standard skin structure, function, and appearance. To achieve this goal, different immune and biological systems participate in coordination through four separate steps, including homeostasis, inflammation, proliferation, and regeneration. Each step involves the function of other cells, cytokines, and growth factors. However, chronic ulcers, which are classified into three types of ulcers, namely vascular ulcers, diabetic ulcers, and pressure ulcers, cannot heal through the mentioned natural stages. It causes mental and physical problems for these people and, as a result, imposes high economic and social costs on society. In this regard, using a system that can accelerate the healing process of such chronic wounds, as an urgent need in the community, should be considered. Therefore, in this study, the innovations of drug delivery systems for the healing of chronic wounds using hydrogels, nanomaterial, and membranes are discussed and reviewed.

In this study, the effect of different parameters on the fluid transport in a fractured micromodel has been investigated. All experiments in this study have been conducted in a glass micromodel. Since the state of wetting is important in the micromodel, the wetting experiments have been conducted to determine the state of wetting in the micromodel. The used micromodel was wet by water and non-wet regarding normal decane. The fracture network, distribution of pore size, matrix construction, and injection rate are the most important parameters affecting the process. Therefore, the influence of these parameters was studied using five different patterns (A to E). The obtained results from pattern A showed that increasing water injection the flow rate results in both higher rate of imbibition and higher ultimate recovery. Pattern B, which was characterized with higher porosity and permeability, was employed to study the effect of matrix pore size distribution on the imbibition process. Compared to pattern A, a higher normal decane production was observed in this pattern. Patterns C and D were designed to understand the impact of lateral fractures on the displacement process. Higher ultimate recoveries were obtained in these patterns. A system of matrix-fracture was designed (pattern E) to evaluate water injection performance in a multi-block system. Injection of water with the flow rate of 0.01 cc/min could produce 15% of the oil available in the system. While in the test with the flow rate of 0.1 cc/min, a normal decane recovery of 0.28 was achieved.

Due to the increasing limitations of water resources, application of desalination plants is expanding. One of the constraints associated with desalination plant operation is the production of concentrated solution, which is known as brine and can lead to critical challenges in the environment due to its high level of salinity. In this regard, many different disposal options used recently to control and prevent the environmental issues may be caused by the brine. Evaporation ponds, surface water discharge, and deep well injection are considered as the most well-known options to properly dispose concentrated brine. However, the application of these methods is highly restricted by capital cost and their limited uses. The treatment methods vary in terms of their ability in organics removal and can be divided into three different conventional groups as biological, physicochemical, and oxidation. In recent years, more attention has been paid to membrane-based technologies due to their economic performance in recovering precious resources and providing potable water with high recovery rates. This book chapter provides some critical reviews on recent technologies including treatment operations and disposal options to manage concentrated solutions from desalination plants. Finally, electrodialysis, forward osmosis, and membrane distillation as emerging membrane processes are examined in this chapter.