No abstract

No abstract

No abstract

Laser ablation inductively coupled plasma mass spectrometry using a quadrupole-based mass spectrometer (LA-ICP-QMS) was applied for the analysis of powdered zeolites (microporous aluminosilicates) used for clean-up procedures. For the quantitative determination of trace element concentrations three geological reference materials, granite NIM-G, lujavrite NIM-L and syenite NIM-S, from the National Institute for Metallurgy (South Africa) with a matrix composition corresponding to the zeolites were employed. Both the zeolites and reference materials were fused with a lithium borate mixture to increase the homogeneity and to eliminate mineralogical effects. In order to compare two different approaches for the quantification of analytical results in LA-ICP-MS relative sensitivity coefficients (RSCs) of chemical elements and calibration curves were measured using the geostandards. The experimentally obtained RSCs are in the range of 0.2-6 for all elements of interest. Calibration curves for trace elements were measured without and with Li or Ti as internal standard element. With a few exceptions the regression coefficients of the calibration curves are better than 0.993 with internal standardization. NIM-G granite reference material was employed to evaluate the accuracy of the technique. Therefore, the measured concentrations were corrected with RSCs which were determined using lujavrite reference material NIM-L. This quantification method provided analytical results with deviations of 1-11% from the recommended and proposed values in granite reference material NIM-G, except for Co, Cs, La and Tb. The relative standard deviation (RSD) of the determination of the trace element concentration (n = 5) is about 1% to 6% using Ti as internal standard element. Detection limits of LA-ICP-QMS in the lower microg/g range (from 0.03 microg/g for Lu, Ta and Th to 7.3 microg/g for Cu, with the exception of La) have been achieved for all elements of interest. Under the laser ablation conditions employed (lambda: 266 nm, repetition frequency: 10 Hz, pulse energy: 10 mJ, laser power density: 6 x 10(9) W/cm2) fractionation effects of the determined elements relative to the internal standard element Ti were not observed.

A commercial multimode sample introduction system (MSIS) was characterized for simultaneous multielement hydride and nonhydride-forming elements (As, Bi, Co, Cr, Fe, Mn, Mo, Ni, Sb, Se, Sn, Ti, V, W) in high alloy steels and nickel alloys by axially viewed ICP-AES. Vapor formed by the NaBH 4 reaction and aerosol from a specially designed dual conical spray chamber and pneumatic nebulizer were injected simultaneously into a robust plasma. Spectroscopic effects caused by major and minor elements and nonspectroscopic interferences induced by matrix concomitants were evaluated both for conventional nebulization and for hydride generation. The objective of the study was to establish optimized operating conditions whereby both nonhydride and hydride forming elements could be determined simultaneously. It was observed that the sensitivities of the 'hydride generating' elements using a MSIS, were similar to those observed using conventional hydride generation. In comparison to conventional pneumatic nebulization, hydride LODs, were enhanced significantly by factors varying from about 2-20. Limits of detection using the MSIS, for nonhydride elements (Co, Cr, Fe, Mn, Mo, Ni, Ti, V, W) were similar to those reported for the conventional sample introduction system. Several fundamental parameters such as Mg II 280.270/Mg I 285.213 nm ratios, excitation temperature (T ex ) and the effect of hydrogen were also determined. The effect of hydrogen, formed during hydride generation, on intensities of nonhydride and hydride forming elements and excitation temperature was evaluated. This is important because hydrogen can modify the properties of the ICP. The effect of variable concentrations of tartaric acid, L-cystein, EDTA, and 1,1,3,3-tetramethy-2-thiourea as retarding agents for reducing deleterious effects of Ni was investigated. The accuracy of the procedure was verified by analyzing several certified reference metallurgical samples. An important conclusion of this multielement study is that the application of the MSIS for simultaneous determination of hydride forming and non-hydride forming elements in complex metallurgical samples by ICP-AES is constrained by matrix derived spectral line interferences.