Atmospheric water is a resource equivalent to ~10% of all fresh water in lakes on Earth. However, an efficient process for capturing and delivering water from air, especially at low humidity levels (down to 20%), has not been developed. We report the design and demonstration of a device based on a porous metal-organic framework {MOF-801, [ZrO(OH)(fumarate)]} that captures water from the atmosphere at ambient conditions by using low-grade heat from natural sunlight at a flux of less than 1 sun (1 kilowatt per square meter). This device is capable of harvesting 2.8 liters of water per kilogram of MOF daily at relative humidity levels as low as 20% and requires no additional input of energy.

Water scarcity is a particularly severe challenge in arid and desert climates. While a substantial amount of water is present in the form of vapour in the atmosphere, harvesting this water by state-of-the-art dewing technology can be extremely energy intensive and impractical, particularly when the relative humidity (RH) is low (i.e., below ~40% RH). In contrast, atmospheric water generators that utilise sorbents enable capture of vapour at low RH conditions and can be driven by the abundant source of solar-thermal energy with higher efficiency. Here, we demonstrate an air-cooled sorbent-based atmospheric water harvesting device using the metal−organic framework (MOF)-801 [Zr6O4(OH)4(fumarate)6] operating in an exceptionally arid climate (10–40% RH) and sub-zero dew points (Tempe, Arizona, USA) with a  thermal efficiency (solar input to water conversion) of ~14%. We predict that this device delivered over 0.25 L of water per kg of MOF for a single daily cycle.

Methylammonium lead halide (MAPbX3 ) perovskites exhibit exceptional carrier transport properties. But their commercial deployment as solar absorbers is currently limited by their intrinsic instability in the presence of humidity and their lead content. Guided by our theoretical predictions, we explored the potential of methylammonium bismuth iodide (MBI) as a solar absorber through detailed materials characterization. We synthesized phase-pure MBI by solution and vapor processing. In contrast to MAPbX3, MBI is air stable, forming a surface layer that does not increase the recombination rate. We found that MBI luminesces at room temperature, with the vapor-processed films exhibiting superior photoluminescence (PL) decay times that are promising for photovoltaic applications. The thermodynamic, electronic, and structural features of MBI that are amenable to these properties are also present in other hybrid ternary bismuth halide compounds. Through MBI, we demonstrate a lead-free and stable alternative to MAPbX3 that has a similar electronic structure and nanosecond lifetimes.

Atmospheric water harvesting (AWH) is the capture and collection of water that is present in the air either as vapor or small water droplets. AWH has been recognized as a method for decentralized water production, especially in areas where liquid water is physically scarce, or the infrastructure required to bring water from other locations is unreliable or infeasible. The main methods of AWH are fog harvesting, dewing, and utilizing sorbent materials to collect vapor from the air. In this paper, we first distinguish between the geographic/climatic operating regimes of fog harvesting, dewing, and sorbentbased approaches based on temperature and relative humidity (RH). Because utilizing sorbents has the potential to be more widely applicable to areas which are also facing water scarcity, we focus our discussion on this approach. We discuss sorbent materials which have been developed for AWH and the material properties which affect system-level performance. Much of the recent materials development has focused on a single material metric, equilibrium vapor uptake in the material (kg of water uptake per kg of dry adsorbent), as found from the adsorption isotherm. This equilibrium property alone, however, is not a good indicator of the actual performance of the AWH system. Understanding material properties which affect heat and mass transport are equally important in the development of materials and components for AWH, because resistances associated with heat and mass transport in the bulk material dramatically change the system performance. We focus our discussion on modeling a solar thermal-driven system. Performance of a solar-driven AWH system can be characterized by different metrics, including L of water per m 2 device per day or L of water per kg adsorbent per day. The former metric is especially important for systems driven by low-grade heat sources because the low power density of these sources makes this technology land area intensive. In either case, it is important to include rates in the performance metric to capture the effects of heat and mass transport in the system. We discuss our previously developed modeling framework which can predict the performance of a sorbent material packed into a porous matrix. This model connects mass transport across length scales, considering diffusion both inside a single crystal as well as macroscale geometric parameters, such as the thickness of a composite adsorbent layer. For a simple solar thermal-driven adsorption-based AWH system, we show how this model can be used to optimize the system. Finally, we discuss strategies which have been used to improve heat and mass transport in the design of adsorption systems and the potential for adsorption-based AWH systems for decentralized water supplies.