The paper reviews the state-of-art for micro optical fluidic systems (MOFS), or optofluidics, which employs optics and fluidics in a microsystem environment to perform novel functionalities and in-depth analysis in the biophysical area. Various topics, which include the introduction of MOFS in biomedical engineering, the implementation of near-field optics and also the applications of MOFS to biophysical studies, are discussed. Different optical detection techniques, such as evanescent wave, surface plasmon resonance, surface enhanced Raman scattering, resonators and transistors, have been studied extensively and integrated into MOFS. In addition, MOFS also provides a platform for various studies of cell biophysics, such as cell mass determination and cell Young's modulus measurement.

Polarization-contrast microscopy coupled with an atomic force microscope is utilized to attain far-field optical images of the multipolar surface plasmon resonance (SPR) modes of single gold nano-rod. Modulated standing modes resulted from the interference of longitudinal SPR modes and incident light are observed and studied. By counting the average distance of adjacent beats on this single gold nano-rod, the wave vector of longitudinal SPR modes can be obtained. We found a linear relationship between the wave vectors of the incident light and the induced SPR modes. Experimental results demonstrate a feasible way on acquiring plasmonic optical properties from an individual single gold nano-rod.

In this paper, a periodic metallic–dielectric nanorod array which consists of Si nanorods coated with 30 nm Ag thin film set in a hexagonal configuration is fabricated and characterized. The fabrication procedure is performed by using nanosphere lithography with reactive ion etching, followed by Ag thin-film deposition. The mechanism of the surface and gap plasmon modes supported by the fabricated structure is numerically demonstrated by the three-dimensional finite element method. The measured and simulated absorptance spectra are observed to have a same trend and a qualitative fit. Our fabricated plasmonic sensor shows an average sensitivity of 340.0 nm/RIU when applied to a refractive index sensor ranging from 1.0 to 1.6. The proposed substrates provide a practical plasmonic nanorod-based sensing platform, and the fabrication methods used are technically effective and low-cost.

We numerically and theoretically investigate a highly sensitive and tunable plasmonic refractive index sensor that is composed of a metal-insulator-metal waveguide with a side-coupled nanoring, containing silver nanorods using the finite element method. Results reveal that the presence of silver nanorods in the nanoring has a significant impact on sensitivity and tunability performance. It gives a flexible way to tune the system response in the proposed structure. Our designed sensor has a sensitivity of 2080 nm/RIU (RIU is the refractive index unit) along with a figure of merit and a quality factor of 29.92 and 29.67, respectively. The adequate refractive index sensitivity can increase by adding the silver nanorods in a nanoring, which can induce new surface plasmon polaritons (SPPs) modes that cannot be found by a regular nanoring. For a practical application, a valid introduction of silver nanorods in the nanoring can dramatically reduce the dimension of the proposed structure without sacrificing performance.

No abstract

In this paper, the coupled Ag-shell/dielectric-core nanorod for sensor application is investigated and the different dielectric core plasmonic metamaterial is adopted in our design. The operational principle is based on the concept of combining the lattice resonance, localized surface plasmon resonance (SPR), and cavity plasmon resonance modes within the nanostructure. The underlying mechanisms are investigated numerically by using the three-dimensional finite element method and the numerical results of coupled solid Ag nanorods are included for comparison. The characteristic absorptance/reflectance peaks/dips have been demonstrated to be induced by different plasmonic modes that could lead to different responses required for plasmonic sensors. A nearly perfect absorptance and an approximate zero reflectance with a sharp band linewidth are obtained from the proposed system, when operated as an SPR sensor with the sensitivity and figure of merit of 757.58 nm/RIU (RIU is the refractive index unit) and 50.51 (RIU –1 ), respectively. Our work provides a promising method for the future developments of more advanced metamaterial absorber for chemical sensing, thermal radiation tailoring, field enhanced spectroscopy, and general filtering applications.

No abstract

An ultra-high plasmonic refractive index sensing structure composed of a metal–insulator–metal (MIM) waveguide coupled to a T-shape cavity and several metal nanorod defects is proposed and investigated by using finite element method. The designed plasmonic MIM waveguide can constitute a cavity resonance zone and the metal nanorod defects can effectively trap the light in the T-shape cavity. The results reveal that both the size of defects in wider rectangular cavity and the length of narrower rectangular cavity are primary factors increasing the sensitivity performance. The sensitivity can achieve as high as 8280 nm/RIU (RIU denotes the refractive index unit), which is the highest sensitivity reported in plasmonic MIM waveguide-based sensors to our knowledge. In addition, the proposed structure can also serve as a temperature sensor with temperature sensitivity as high as 3.30 nm/°C. The designed structure with simplicity and ease of fabrication can be applied in sensitivity nanometer scale refractive index sensor and may potentially be used in optical on-chip nanosensor.