Evidence of wall slip and magnitude of yield stress are examined for colloidal gels consisting of hydrophobic silica, polyether, and lithium salts using geometries with serrated, smooth, hydrophilic and hydrophobic surfaces. Serrated plates, which provide minimal wall slip, are used to compare different methods of measuring yield stress: conventional extrapolation of shear stress in steady shear experiments and dynamic experiments at large strain amplitudes. In the latter, the yield stress is denoted by the maximum in the elastic stress, the product of the elastic modulus and strain (G Ј ␥), when plotted as a function of strain amplitude. Although excellent agreement is observed in the yield stress values using both these techniques, the dynamic method seems preferable considering its experimental ease, accuracy, and lack of extrapolation. In the presence of smooth geometries, the silica gels show evidence of wall slip with a concomitant decrease in yield stress. Using underestimation of yield stress as a measure of wall slip, we find slip to be unaffected by changes in the gel modulus obtained through incorporation of additional silica or salts. The use of smooth surfaces compared to serrated surfaces leads to approximately a 60% reduction in yield stress for all such samples. Finally, control of wall slip is attempted using plates modified to have different surface energies. Hydrophobic plates reduce slip significantly and produce data comparable to those with the serrated plates. In contrast, hydrophilic plates have minimal effect on slip and produce data analogous to those obtained using smooth plates. These results can be explained based on the fact that the particle-lean layer, responsible for slip, remains so with hydrophilic plates as it repels the hydrophobic silica particles in favor of the polar solvent. In contrast, the hydrophobic silica interacts with the hydrophobic plates, thus reducing slip.

The threat associated with chemical warfare agents (CWAs) motivates the development of new materials to provide enhanced protection with a reduced burden. Metal-organic frame-works (MOFs) have recently been shown as highly effective catalysts for detoxifying CWAs, but challenges still remain for integrating MOFs into functional filter media and/or protective garments. Herein, we report a series of MOF-nanofiber kebab structures for fast degradation of CWAs. We found TiO coatings deposited via atomic layer deposition (ALD) onto polyamide-6 nanofibers enable the formation of conformal Zr-based MOF thin films including UiO-66, UiO-66-NH , and UiO-67. Cross-sectional TEM images show that these MOF crystals nucleate and grow directly on and around the nanofibers, with strong attachment to the substrates. These MOF-functionalized nanofibers exhibit excellent reactivity for detoxifying CWAs. The half-lives of a CWA simulant compound and nerve agent soman (GD) are as short as 7.3 min and 2.3 min, respectively. These results therefore provide the earliest report of MOF-nanofiber textile composites capable of ultra-fast degradation of CWAs.

Rapid room-temperature synthesis of metal-organic frameworks (MOFs) is highly desired for industrial implementation and commercialization. Here we find that a (Zn,Cu) hydroxy double salt (HDS) intermediate formed in situ from ZnO particles or thin films enables rapid growth (<1 min) of HKUST-1 (Cu3(BTC)2) at room temperature. The space-time-yield reaches >3 × 10(4) kg·m(-3)·d(-1), at least 1 order of magnitude greater than any prior report. The high anion exchange rate of (Zn,Cu) hydroxy nitrate HDS drives the ultrafast MOF formation. Similarly, we obtained Cu-BDC, ZIF-8, and IRMOF-3 structures from HDSs, demonstrating synthetic generality. Using ZnO thin films deposited via atomic layer deposition, MOF patterns are obtained on pre-patterned surfaces, and dense HKUST-1 coatings are grown onto various form factors, including polymer spheres, silicon wafers, and fibers. Breakthrough tests show that the MOF-functionalized fibers have high adsorption capacity for toxic gases. This rapid synthesis route is also promising for new MOF-based composite materials and applications.

No abstract

Fiber@ALD@MOF structures fabricated via ALD and layer-by-layer MOF synthesis show good conformality and high adsorption capacity.

The use of nanocomposites constitutes a versatile and robust approach in the development of novel electrolytes with tailored electrochemical and mechanical characteristics. In this study, we examine the morphology, rheology, and ion‐transport properties of two types of nanocomposite electrolyte gels, one consisting of branched silica nanoparticles and the other composed of hectorite clay. In the first system with hydrophobic (fumed) silica, oligomers of poly(ethylene oxide) (PEO), and lithium salt, the silica acts as a passive filler and does not participate in ion transport. The electrochemical properties are controlled by the salt–PEO electrolyte, allowing for ionic conductivities greater than 10–3 S cm–1 at ambient temperature. At sufficiently high concentrations, the silica forms an elastic gel possessing a large open network structure that provides for unimpeded ion mobility. In the second system composed of lithium‐exchanged hectorite filler, the nanoscale platelets serve as the anion. This active filler yields ionic conductivities in excess of 10–4 S cm–1 and lithium transference numbers approaching unity. Similar to fumed silica, the hectorite clay also forms an elastic gel network. However, the morphologies of the two systems are distinctively different both in terms of network structure and characteristic length scale. These morphological differences manifest themselves in different rheological responses with regard to gel modulus and yield stress.

While metal‐organic frameworks (MOFs) show great potential for gas adsorption and storage, their powder form limits deployment opportunities. Integration of MOFs on polymeric fibrous scaffolds will enable new applications in gas adsorption, membrane separation, catalysis, and toxic gas sensing. Here, we demonstrate a new synthesis route for growing MOFs on fibrous materials that achieves high MOF loadings, large surface areas and high adsorptive capacities. We find that a nanoscale coating of Al2O3 formed by atomic layer deposition (ALD) on the surface of nonwoven fiber mats facilitates nucleation of MOFs on the fibers throughout the mat. Functionality of MOFs is fully maintained after integration, and MOF crystals are well attached to the fibers. Breakthrough tests for HKUST‐1 MOFs [Cu3(BTC)2] on ALD‐coated polypropylene fibers reveal NH3 dynamic loadings up to 5.93 ± 0.20 mol/kg(MOF+fiber). Most importantly, this synthetic approach is generally applicable to a wide range of polymer fibers (e.g., PP, PET, cotton) and MOFs (e.g., HKUST‐1, MOF‐74, and UiO‐66).

The threat associated with chemical warfare agents (CWAs) motivates the development of new materials to providee nhanced protection with ar educed burden. Metalorganic frame-works (MOFs) have recently been shown as highly effective catalysts for detoxifying CWAs,but challenges still remain for integrating MOFs into functional filter media and/or protective garments.Herein, we report aseries of MOFnanofiber kebab structures for fast degradation of CWAs.W e found TiO 2 coatings deposited via atomic layer deposition (ALD) onto polyamide-6 nanofibers enable the formation of conformal Zr-based MOF thin films including UiO-66, UiO-66-NH 2 ,a nd UiO-67. Cross-sectional TEM images show that these MOF crystals nucleate and growdirectly on and around the nanofibers,with strong attachment to the substrates.These MOF-functionalized nanofibers exhibit excellent reactivity for detoxifying CWAs.T he half-lives of aC WA simulant compound and nerve agent soman (GD) are as short as 7.3 min and 2.3 min, respectively.T hese results therefore provide the earliest report of MOF-nanofiber textile composites capable of ultra-fast degradation of CWAs.