Polypyrrole (PPy) is an inherently conducting polymer that has shown great promise for biomedical applications within the nervous system. However, to effectively use PPy as a biomaterial implant, it is important to understand and reproducibly control the electrical properties, physical topography, and surface chemistry of the polymer. Although there is much research published on the use of PPy in various applications, there is no systematic study linking the methodologies used for PPy synthesis to PPy's basic polymeric properties (e.g., hydrophilicity, surface roughness), and to the biological effects these properties have on cells. Electrochemically synthesized PPy films differ greatly in their characteristics depending on synthesis parameters such as dopant, substrate, and thickness, among other parameters. In these studies, we have used three dopants (chloride (Cl), tosylate (ToS), polystyrene sulfonate (PSS)), two substrates (gold and indium tin oxide-coated glass), and a range of thicknesses, to measure and compare the biomedically-important characteristics of surface roughness, contact angle, conductivity, dopant stability, and cell adhesion (using PC-12 cells and Schwann cells). As predicted, we discovered large differences in roughness depending on the dopant used and the thickness of the film, while substrate choice had little effect. From contact angle measurements, PSS was found to yield the most hydrophilic material, most likely because of free charges from the long PSS chains exposed on the surface of the PPy. ToS-doped PPy films were tenfold more conductive than Cl-or PSS-doped films. X-ray photoelectron spectroscopy studies were used to evaluate dopant concentrations of PPy films stored in water and phosphate buffered saline over 14 days, and conductance studies over the same timeframe measured electrical stability. PSS proved to be the most stable dopant, though all films experienced significant decay in conductivity and dopant concentration. Cell adhesion studies demonstrated the dependence of cell outcome on film thickness and dopant choice. The strengths and weaknesses of different synthesis parameters, as demonstrated by these experiments, are critical design factors that must be leveraged when designing biomedical implants. The results of these studies should provide practical insight to researchers working with conducting polymers, and particularly PPy, on the relationships between synthesis parameters, polymeric properties, and biological compatibility.

No abstract

Development of “organ-on-a-chip” systems for neuroscience applications are lagging due in part to the structural complexity of the nervous system and limited access of human neuronal & glial cells. In addition, rates for animal models in translating to human success are significantly lower for neurodegenerative diseases. Thus, a preclinical in vitro human cell-based model capable of providing critical clinical metrics such as nerve conduction velocity and histomorphometry are necessary to improve prediction and translation of in vitro data to successful clinical trials. To answer this challenge, we present an in vitro biomimetic model of all-human peripheral nerve tissue capable of showing robust neurite outgrowth (~5 mm), myelination of hNs by primary human Schwann cells (~5%), and evaluation of nerve conduction velocity (0.13–0.28 m/sec), previously unrealized for any human cell-based in vitro system. To the best of our knowledge, this Human Nerve-on-a-chip (HNoaC) system is the first biomimetic microphysiological system of myelinated human peripheral nerve which can be used for evaluating electrophysiological and histological metrics, the gold-standard assessment techniques previously only possible with in vivo studies.

Nerve guidance conduits (NGCs) are FDA-approved devices used to bridge gaps across severed nerve cables and help direct axons sprouting from the proximal end toward the distal stump. In this paper we present the development of a novel electrically conductive, biodegradable NGC made from a polypyrrole-block-polycaprolactone (PPy-PCL) copolymer material laminated with poly(lactic-co-glycolic acid) (PLGA). The PPy-PCL has a bulk conductivity ranging 10–20 S/cm and loses 40 wt% after 7 months under physiologic conditions. Dorsal root ganglia (DRG) grown on flat PPy-PCL/PLGA material exposed to direct current electric fields (EF) of 100 mV/cm for 2 h increased axon growth by 13% (± 2%) towards either electrode of a 2-electrode setup, compared to control grown on identical substrates without EF exposure. Alternating current increased axon growth by 21% (± 3%) without an observable directional preference, compared to the same control group. The results from this study demonstrate PLGA-coated PPy-PCL is a unique biodegradable material that can deliver substrate EF stimulation to improve axon growth for peripheral nerve repair.

These findings demonstrate EF exposure can control Schwann cell alignment and morphology, change ECM bulk/surface architecture, and align ECM structures.

For some professionally, vocationally, or technically oriented careers, curricula delivered in higher education establishments may focus on teaching material related to a single discipline. By contrast, multidisciplinary, interdisciplinary, and transdisciplinary teaching (MITT) results in improved affective and cognitive learning and critical thinking, offering learners/students the opportunity to obtain a broad general knowledge base. Chemistry is a discipline that sits at the interface of science, technology, engineering, mathematics, and medicine (STEMM) subjects (and those aligned with or informed by STEMM subjects). This article discusses the significant potential of inclusion of chemistry in MITT activities in higher education and the real-world importance in personal, organizational, national, and global contexts. It outlines the development and implementation challenges attributed to legacy higher education infrastructures (that call for creative visionary leadership with strong and supportive management and administrative functions), and curriculum design that ensures inclusivity and collaboration and is pitched and balanced appropriately. It concludes with future possibilities, notably highlighting that chemistry, as a discipline, underpins industries that have multibillion dollar turnovers and employ millions of people across the world.

We present a nontraditional fabrication technique for the realization of three-dimensional (3D) microelectrode arrays (MEAs) capable of interfacing with 3D cellular networks in vitro. The technology uses cost-effective makerspace microfabrication techniques to fabricate the 3D MEAs with 3D printed base structures with the metallization of the microtowers and conductive traces being performed by stencil mask evaporation techniques. A biocompatible lamination layer insulates the traces for realization of 3D microtower MEAs (250 μm base diameter, 400 μm height). The process has additionally been extended to realize smaller electrodes (30 μm × 30 μm) at a height of 400 μm atop the 3D microtower using laser micromachining of an additional silicon dioxide (SiO2) insulation layer. A 3D microengineered, nerve-on-a-chip in vitro model for recording and stimulating electrical activity of dorsal root ganglion (DRG) cells has further been integrated with the 3D MEA. We have characterized the 3D electrodes for electrical, chemical, electrochemical, biological, and chip hydration stability performance metrics. A decrease in impedance from 1.8 kΩ to 670 Ω for the microtower electrodes and 55 to 39 kΩ for the 30 μm × 30 μm microelectrodes can be observed for an electrophysiologically relevant frequency of 1 kHz upon platinum electroless plating. Biocompatibility assays on the components of the system resulted in a large range (∼3%–70% live cells), depending on the components. Fourier-transform infrared (FTIR) spectra of the resin material start to reveal possible compositional clues for the resin, and the hydration stability is demonstrated in in-vitro-like conditions for 30 days. The fabricated 3D MEAs are rapidly produced with minimal usage of a cleanroom and are fully functional for electrical interrogation of the 3D organ-on-a-chip models for high-throughput of pharmaceutical screening and toxicity testing of compounds in vitro.

No abstract