Ship engines in the open ocean and Arctic typically combust heavy fuel oil (HFO), resulting in light-absorbing particulate matter (PM) emissions that have been attributed to black carbon (BC) and conventional, soluble brown carbon (brC). We show here that neither BC nor soluble brC is the major light-absorbing carbon (LAC) species in HFO-combustion PM. Instead, "tar brC" dominates. This tar brC, previously identified only in open-biomass-burning emissions, shares key defining properties with BC: it is insoluble, refractory, and substantially absorbs visible and near-infrared light. Relative to BC, tar brC has a higher Angstrom absorption exponent (AAE) (2.5-6, depending on the considered wavelengths), a moderately-high mass absorption efficiency (up to 50% of that of BC), and a lower ratio of sp 2-to sp 3-bonded carbon. Based on our results, we present a refined classification of atmospheric LAC into two sub-types of BC and two sub-types of brC. We apply this refined classification to demonstrate that common analytical techniques for BC must be interpreted with care when applied to tar-containing aerosols. The global significance of our results is indicated by field observations which suggest that tar brC already contributes to Arctic snow darkening, an effect which may be magnified over upcoming decades as Arctic shipping continues to intensify.

Abstract. Organic aerosols (OA) derived from small-scale wood combustion emissions are not well represented by current emissions inventories and models, although they contribute substantially to the atmospheric particulate matter (PM) levels. In this work, a 29 m3 smog chamber in the ILMARI facility of the University of Eastern Finland was utilized to investigate the formation of secondary organic aerosol (SOA) from a small-scale modern masonry heater commonly used in northern Europe. Emissions were oxidatively aged in the smog chamber for a variety of dark (i.e., O3 and NO3) and UV (i.e., OH) conditions, with OH concentration levels of (0.5–5)  ×  106 molecules cm−3, achieving equivalent atmospheric aging of up to 18 h. An aerosol mass spectrometer characterized the direct OA emissions and the SOA formed from the combustion of three wood species (birch, beech and spruce) using two ignition processes (fast ignition with a VOC-to-NOx ratio of 3 and slow ignition with a ratio of 5).Dark and UV aging increased the SOA mass fraction with average SOA productions 2.0 times the initial OA mass loadings. SOA enhancement was found to be higher for the slow ignition compared with fast ignition conditions. Positive matrix factorization (PMF) was used to separate SOA, primary organic aerosol (POA) and their subgroups from the total OA mass spectra. PMF analysis identified two POA and three SOA factors that correlated with the three major oxidizers: ozone, the nitrate radical and the OH radical. Organonitrates (ONs) were observed to be emitted directly from the wood combustion and additionally formed during oxidation via NO3 radicals (dark aging), suggesting small-scale wood combustion may be a significant ON source. POA was oxidized after the ozone addition, forming aged POA, and after 7 h of aging more than 75 % of the original POA was transformed. This process may involve evaporation and homogeneous gas-phase oxidation as well as heterogeneous oxidation of particulate organic matter. The results generally prove that logwood burning emissions are the subject of intensive chemical processing in the atmosphere, and the timescale for these transformations is relatively short, i.e., hours.

BackgroundShip engine emissions are important with regard to lung and cardiovascular diseases especially in coastal regions worldwide. Known cellular responses to combustion particles include oxidative stress and inflammatory signalling.ObjectivesTo provide a molecular link between the chemical and physical characteristics of ship emission particles and the cellular responses they elicit and to identify potentially harmful fractions in shipping emission aerosols.MethodsThrough an air-liquid interface exposure system, we exposed human lung cells under realistic in vitro conditions to exhaust fumes from a ship engine running on either common heavy fuel oil (HFO) or cleaner-burning diesel fuel (DF). Advanced chemical analyses of the exhaust aerosols were combined with transcriptional, proteomic and metabolomic profiling including isotope labelling methods to characterise the lung cell responses.ResultsThe HFO emissions contained high concentrations of toxic compounds such as metals and polycyclic aromatic hydrocarbon, and were higher in particle mass. These compounds were lower in DF emissions, which in turn had higher concentrations of elemental carbon (“soot”). Common cellular reactions included cellular stress responses and endocytosis. Reactions to HFO emissions were dominated by oxidative stress and inflammatory responses, whereas DF emissions induced generally a broader biological response than HFO emissions and affected essential cellular pathways such as energy metabolism, protein synthesis, and chromatin modification.ConclusionsDespite a lower content of known toxic compounds, combustion particles from the clean shipping fuel DF influenced several essential pathways of lung cell metabolism more strongly than particles from the unrefined fuel HFO. This might be attributable to a higher soot content in DF. Thus the role of diesel soot, which is a known carcinogen in acute air pollution-induced health effects should be further investigated. For the use of HFO and DF we recommend a reduction of carbonaceous soot in the ship emissions by implementation of filtration devices.

We characterized the chemical composition and optical properties of particulate matter (PM) emitted by a marine diesel engine operated on heavy fuel oil (HFO), marine gas oil (MGO), and diesel fuel (DF). For all three fuels, ∼80% of submicron PM was organic (and sulfate, for HFO at higher engine loads). Emission factors varied only slightly with engine load. Refractory black carbon (rBC) particles were not thickly coated for any fuel; rBC was therefore externally mixed from organic and sulfate PM. For MGO and DF PM, rBC particles were lognormally distributed in size (mode at d rBC ≈120 nm). For HFO, much larger rBC particles were present. Combining the rBC mass concentrations with in situ absorption measurements yielded an rBC mass absorption coefficient MAC BC,780 nm of 7.8 ± 1.8 m 2 /g at 780 nm for all three fuels. Using positive deviations of the absorption Ångström exponent (AAE) from unity to define brown carbon (brC), we found that brC absorption was negligible for MGO or DF PM (AAE(370,880 nm) ≈ 1.0 ± 0.1) but typically 50% of total 370-nm absorption for HFO PM. Even at 590 nm, ∼20 of the total absorption was due to brC. Using absorption at 880 nm as a reference for BC absorption and normalizing to organic PM mass, we obtained a MAC OM,370 nm of 0.4 m 2 /g at typical operating conditions. Furthermore, we calculated an imaginary refractive index of (0.045 ± 0.025)( ∕370 nm) −3 for HFO PM at 370 nm> > 660 nm, more than twofold greater than previous recommendations. Climate models should account for this substantial brC absorption in HFO PM. Plain Language SummaryWe characterized the fundamental properties of marine engine exhaust that are relevant to its aerosol-radiation interactions in climate models. In particular, we focussed on "brown carbon" light absorption (i.e., absorption in excess of that expected for the black carbon in canonical soot). We found that brown carbon can increase the direct radiative forcing of heavy-fuel-oil ship exhaust by 18% over snow.

Gaseous and particulate emissions from a ship diesel research engine were elaborately analysed by a large assembly of measurement techniques. Applied methods comprised of offline and online approaches, yielding averaged chemical and physical data as well as time-resolved trends of combustion by-products. The engine was driven by two different fuels, a commonly used heavy fuel oil (HFO) and a standardised diesel fuel (DF). It was operated in a standardised cycle with a duration of 2 h. Chemical characterisation of organic species and elements revealed higher concentrations as well as a larger number of detected compounds for HFO operation for both gas phase and particulate matter. A noteworthy exception was the concentration of elemental carbon, which was higher in DF exhaust aerosol. This may prove crucial for the assessment and interpretation of biological response and impact via the exposure of human lung cell cultures, which was carried out in parallel to this study. Offline and online data hinted at the fact that most organic species in the aerosol are transferred from the fuel as unburned material. This is especially distinctive at low power operation of HFO, where low volatility structures are converted to the particulate phase. The results of this study give rise to the conclusion that a mere switching to sulphur-free fuel is not sufficient as remediation measure to reduce health and environmental effects of ship emissions.

Heavy fuel oil (HFO) particulate matter (PM) emitted by marine engines is known to contain toxic heavy metals, including vanadium (V) and nickel (Ni). The toxicity of such metals will depend on the their chemical state, size distribution, and mixing state. Using online soot-particle aerosol mass spectrometry (SP-AMS), we quantified the mass of five metals (V, Ni, Fe, Na, and Ba) in HFO-PM soot particles produced by a marine diesel research engine. The in-soot metal concentrations were compared to in-PM2.5 measurements by inductively coupled plasma-optical emission spectroscopy (ICP-OES). We found that <3% of total PM2.5 metals was associated with soot particles, which may still be sufficient to influence in-cylinder soot burnout rates. Since these metals were most likely present as oxides, whereas studies on lower-temperature boilers report a predominance of sulfates, this result implies that the toxicity of HFO PM depends on its combustion conditions. Finally, we observed a 4-to-25-fold enhancement in the ratio V:Ni in soot particles versus PM2.5, indicating an enrichment of V in soot due to its lower nucleation/condensation temperature. As this enrichment mechanism is not dependent on soot formation, V is expected to be generally enriched within smaller HFO-PM particles from marine engines, enhancing its toxicity.

No abstract

Gas-phase emission samples of carbonyl compounds (CCs) were collected from two modern wood combustion appliances. Multiple repetitions were conducted on masonry heater operated with three logwood species (birch, beech, and spruce) and for a pellet boiler operated by softwood pellet with normal combustion and unoptimized combustion (in which the secondary combustion air flow rate was decreased). The sampling of CCs was performed from diluted exhaust using 2,4-dinitrophenylhydrazine (DNPH) cartridges. The CCs-hydrazone derivatives were analyzed by a gas chromatography−selective ion monitoring−mass spectrometry (GC-SIM-MS) method. Twelve (12) CCs were quantified in the masonry heater emissions and 8 in the pellet boiler emissions. The total carbonyl emission factors (EFs) for logwood were determined to be as follows: birch, 113 ± 18 mg kg −1 ; beech, 178 ± 31 mg kg −1 ; spruce, 171 ± 19 mg kg −1 ; and, for softwood pellet with normal combustion, 6 ± 0.9 mg kg −1 and for softwood pellet with unoptimized combustion, 6.5 ± 1 mg kg −1 . In masonry heater operation, birch exhibits the lowest emission factors, compared to other wood types. No significant differences were noticed between the emission of normal and unoptimized combustion for the pellet boiler operation. The emission profile examination showed that formaldehyde and acetaldehyde were the predominated carbonyls in the emission, regardless of the wood type. Time-resolved results obtained via single-photon ionization time-of-flight mass spectrometry (SPI-TOFMS) depict that, in masonry heater emissions, most carbonyls are produced as a new batch of wood is introduced.