The blood-brain barrier (BBB), a unique selective barrier for the central nervous system (CNS), hinders the passage of most compounds to the CNS, complicating drug development. Innovative in vitro models of the BBB can provide useful insights into its role in CNS disease progression and drug delivery. Static transwell models lack fluidic shear stress, while the conventional dynamic in vitro BBB lacks a thin dual cell layer interface. To address both limitations, we developed a microfluidic blood-brain barrier (μBBB) which closely mimics the in vivo BBB with a dynamic environment and a comparatively thin culture membrane (10 μm). To test validity of the fabricated BBB model, μBBBs were cultured with b.End3 endothelial cells, both with and without co-cultured C8-D1A astrocytes, and their key properties were tested with optical imaging, trans-endothelial electrical resistance (TEER), and permeability assays. The resultant imaging of ZO-1 revealed clearly expressed tight junctions in b.End3 cells, Live/Dead assays indicated high cell viability, and astrocytic morphology of C8-D1A cells were confirmed by ESEM and GFAP immunostains. By day 3 of endothelial culture, TEER levels typically exceeded 250 Ω cm(2) in μBBB co-cultures, and 25 Ω cm(2) for transwell co-cultures. Instantaneous transient drop in TEER in response to histamine exposure was observed in real-time, followed by recovery, implying stability of the fabricated μBBB model. Resultant permeability coefficients were comparable to previous BBB models, and were significantly increased at higher pH (>10). These results demonstrate that the developed μBBB system is a valid model for some studies of BBB function and drug delivery.

No abstract

Abstract:We demonstrate the implementation of a compact tunable-focus liquid lens suitable for adaptive eyeglass application. The lens has an aperture diameter of 32 mm, optical power range of 5.6 diopter, and electrical power consumption less than 20 mW. The lens inclusive of its piezoelectric actuation mechanism is 8.4 mm thick and weighs 14.4 gm. The measured lens RMS wavefront aberration error was between 0.73 µm and 0.956 µm.

Thermoelectric (TE) properties of the coevaporated Bi2Te3 and Sb2Te3 films are measured from 100 to 300 K for Seebeck coefficient αS and from 5 to 300 K for electrical resistivity ρe, mobility μe, and Hall coefficient RH. For the low-temperature characterization of TE films, the conditions for coevaporation deposition of Bi, Te, and Sb to form Bi2Te3 and Sb2Te3 films are also investigated, including substrate material, substrate temperature Tsub, and elemental flux ratio (FR). The resublimation of Te occurring above 473 K significantly affects the film composition and quality. Our optimal deposition conditions for Bi2Te3 films are Tsub=533 K and FR=2.4, and those for Sb2Te3 films are Tsub=503 K and FR=3.0. The TE properties of both films are strongly temperature dependent, while Bi2Te3 films show a stronger temperature dependence than Sb2Te3 films due to different major scattering mechanisms. αS of both the coevaporated films are close to or higher than those of bulk materials, but ρe is much higher (due to lower carrier concentrations for Sb2Te3 films and lower μe for Bi2Te3 films). Also, no freeze-out regime is found for both Bi2Te3 and Sb2Te3 films at low temperatures. The room-temperature power factors of αS2/ρe for Bi2Te3 and Sb2Te3 films are 2.3 and 2.0 mW/K2 m, and the maxima are 2.7 mW/K2 m for Bi2Te3 at T=220 K and 2.1 mW/K2 m for Sb2Te3 at T=280 K. Shadow mask technique is successfully used for the micropatterning (20 μm) of TE films with no significant change in properties.

This paper reports the design, fabrication and testing of an energy scavenger that generates power from the wing motion of a Green June Beetle (Cotinis nitida) during its tethered flight. The generator utilizes non-resonant piezoelectric bimorphs operated in the d 31 bending mode to convert mechanical vibrations of a beetle into electrical output. The available deflection, force, and power output from oscillatory movements at different locations on a beetle are measured with a meso-scale piezoelectric beam. This way, the optimum location to scavenge energy is determined, and up to ∼115 μW total power is generated from body movements. Two initial generator prototypes were fabricated, mounted on a beetle, and harvested 11.5 and 7.5 μW in device volumes of 11.0 and 5.6 mm 3 , respectively, from 85 to 100 Hz wing strokes during the beetle's tethered flight. A spiral generator was designed to maximize the power output by employing a compliant structure in a limited area. The necessary technology needed to fabricate this prototype was developed, including a process to machine high-aspect ratio devices from bulk piezoelectric substrates with minimum damage to the material using a femto-second laser. The fabricated lightweight spiral generators produced 18.5-22.5 μW on a bench-top test setup mimicking beetles' wing strokes. Placing two generators (one on each wing) can result in more than 45 μW of power per insect. A direct connection between the generator and the flight muscles of the insect is expected to increase the final power output by one order of magnitude.